I love my falcons and the customer service is remarkable. Mr. Pitts spent a few hours on the phone with me helping me find a solution when I had an issue. I don't have any experience with other boards.
+1 Falcon. Great controller and you really can't beat the customer service David offers.
Falcon has a web interface.
J1Sys P12's have a web interface.
E682 has a web interface.
Those are the ones I own (but I want to sell off the 682). The falcon is my personal choice (for whatever that is worth) for best of the lot. I live in Milwaukee, well north of you. Two of my falcons have been outside in CG1500 boxes since early October and will be there until probably Feb or March whenever we get a decent day to go outside and pack stuff up. Last year I ran the P12's. They went out in November and were there until early march when we got good weather to bring them in. They are primitive by comparison to the Falcon. And so is the 682.
Of all those, the Falcon has the most flexibility, best web interface, most expansion options and best bang for the buck. It requires no software as firmware updates are done OTA. It has a control button set on the board and a OLED display for initial setup. Is it the cheapest? No. But if you factor in features you get for the price, frankly its a winner in virtually every chart you can measure it by. There are times where you get what you pay for. This is one of them.
As for easy setup, well, it can be. They all can be. Not too many of the current generation of controllers require a degree in quantum mechanics to make them blink lights. I suppose it depends on what you are doing and what your capability is. If you have a grasp at what you are doing, then you won't have any issues with any of the above listed controllers. I mean, there are folks on this forum who have never put up any sort of display before and were able to deploy and configure their falcon controllers. You obviously have a level of knowledge far above theirs. You won't have a problem. I won't say its stupid simple, but its obvious simple. Though, I found the interface for the E682 not to my liking. Was not a good fit for me personally. Jim puts out a quality built product so maybe it will work for you and it works for a lot of people and has for a long time. Out of the box the Falcon was pretty obvious how to run it, how to configure it, and how it should be used. David even added at least one feature to the firmware I had asked for that makes the interface even more user friendly. Kinda hard to beat that customer support don't you think?
The falcons have two temperature sensor inputs, one of which comes supplied with a thermister and you can add a second for remote monitoring of, say a PSU enclosure or external temps if you wish. The web interface shows these readings as well as the voltage inputs to the board right on the status page. So you can monitor the temps right from your web browser.
The latest firmware for the Falcon provides for saving and loading of configurations (XML files). So duplicating setups is easy, changing from Halloween to Christmas is easy. It also allows naming of each string and substring so its extremely obvious what is connected to what port in what order. Not sure where to plug something? Pull up the string config page on your phone/tablet, and look. That easy.
In addition to the 16 pixel outputs, it also has 4 DMX capable outputs for long haul runs or other DMX fixtures like moving heads, floods, pars, etc. And they can also be configured for RS485 outputs so you can run pixel data hundreds of feet. The Falcon also has expansion boards to up the port count to 32 and an differential board that can drive 16 more ports hundreds of feet away. You aren't going to find that expansion ability in any other controller. Period.
And there is smaller F4 boards with 4 outputs for spots where you don't need big boards. Same interface. Same capabilities so you have instant familiarity with the board if you already have used the F16.
As for 5a outputs, most controllers support that. However, just saying here, the majority of my display is NOT powered direct from the controller. Some is. Most is not. There is NO requirement to power directly from a controller. Any controller. Can it? Yes, the falcon is rated at 5a each output, but I believe its limited to 30a per bank of 8 outputs. Mine is fused at 20a per bank because, as I said, I don't power most of my display off the controller. In fact my megatree consumes absolutely no power from my controller. It has a set of dedicated PSUs and only data and ground come from the controller. So if you think of a controller as a Data Supply and separate that from your Power Supply, and controller will do. There are many options for power distribution blocks, David makes one. And there are options from the automotive, marine and aviation industries for power distribution as well. Anything from a simple 4 output fuse block to complex power distribution panels are out there for the asking.
The best pixel controller will be the one that puts your show away for you when the season is over 🙂
On a side note , I had the opportunity to physically setup a Diyledexpress 6 port bridge this past weekend for a fellow here that is new to the hobby .
I was surprised how well this well this jewel of a bridge was in ease of access and setup .
Also was equally impressed that it had pixel capability for ws 2811 .
For some this just could be the ultimate pixel controller. :disgust:
angus40 wrote:The best pixel controller will be the one that puts your show away for you when the season is over 🙂On a side note , I had the opportunity to physically setup a Diyledexpress 6 port bridge this past weekend for a fellow here that is new to the hobby .
I was surprised how well this well this jewel of a bridge was in ease of access and setup .
Also was equally impressed that it had pixel capability for ws 2811 .
For some this just could be the ultimate pixel controller. :disgust:
I saw the potential in the bridge years ago and use 2 of them in my show to run a variety of controllers: 27 channel DMX, DM103, 16 channel LOR and now use pixel extender to run WS2811.
It works great as a pixel controller but you have to be wary that current firmware restricts bridge to 12 universes total. This would include any outputs using DMX as well as those utilizing a pixel extender.
Right now, I am utilizing 3 universes of DMX (one on each port) and one port is running 280 pixels (spanning 2 universes) all on one bridge and runs flawlessly. Love this board!
Much has been said. I think you will be satisfied any way you go. However, only you know what the requirements are and if there are limitations to certain controllers.
I deployed a light show in a town park this year, where people can walk around lighted features. I personally went with Falcon controllers after testing one myself first, after years of using sandevices. They are, as has been said previously, much more polished, feature-rich, and flexible than some others available. All will do what you want, but I do think they are the easiest to use.
I have 13 F16's in use in the park show. They have been running solid, no issues since a week before thanksgiving. I was very pleased with the ease of setup and reduced complexity compared to what would have been involved had I gone with a different vendor's product.
The third version is rumored to have a built-in switch and possibly the ability to run a show without the pi. These are things to consider as well.
