I was just wondering what controllers people are using for their pixels in things like a mega tree?
I've got lots of LED lights which I have used in a static display but am hoping to get my first 'proper' display up and running this year with Renard controllers (64XC, plus 32). I am also interested in getting a pixel tree running using James' topper kit. As I would be using Renard boards for the LEDs I was wondering if there was a particular controller that would be better to use for the pixels. The PX-1 seems like a good choice as it could be easily added with other Renard boards, but would I be better with the e682? Are they easily added in to a display with Renard boards?
I was planning to use Vixen, which I'm pretty sure I could control all the Renard boards with, including the PX-1. Is the e682 controllable using Vixen aswell?
I would imagine you are going to need to go the E682 or 6804 route.
The PX-1 is great for just a few pixels, but with a mega tree you are going to quickly run out of channels you can use (check here for the PX-1, and herefor the total Renard run). I think adding the sandevice controller will be simpler.
I started out with Renards and added the 6804, was pretty easy, and it could drive the renards so it didn't add a lot of complexity to the setup.
Yes, Vixen can control the e682
you can make a great 180 degree 8' pixel tree using 2 px-1s you can always use more than 1 usb/serial port as I did this year running the px-1s ports at 115200 I had 6 strings of 50 pixels and a large star on top and still had free channels too use my renards ran off own port also had no problems with it at all being new I found it alot easier too use than figuring out the e682 or 6804 was simple too add 2 of them and 1 power supply and power injection too a tree since it was all in one location here is a little test video of my tree it is 8" tall tree and star is almost 4' tall
Heldwhat Christmas wrote:I would imagine you are going to need to go the E682 or 6804 route.
The PX-1 is great for just a few pixels, but with a mega tree you are going to quickly run out of channels you can use (check here for the PX-1, and herefor the total Renard run). I think adding the sandevice controller will be simpler.I started out with Renards and added the 6804, was pretty easy, and it could drive the renards so it didn't add a lot of complexity to the setup.
Yes, Vixen can control the e682
There you go, 1 vote for each. :thup2:
Either would certainly work, really depends on personal preference and what your future plans are. The 682/6804 was a little intimidating at first, but was actually pretty easy once I started playing with it.
Thank guys, although none the wiser!!
Not sure if I'll get it done this year as I need to get the normal Renard controllers up and running first, which is a lot to learn as it is. However, my possible thoughts are the PX-1 for an 8' mega tree, it seems like it would be easier to start with. At some point I'd love to build a matrix and this looks far to much for the PX-1, so it appears that would require something more like the e682.
I'm just trying to decide whether the best thing would be to start with the PX-1 as a way to start learning about pixels, basically a good stepping stone to the e682.
mutleyrover wrote:I'm just trying to decide whether the best thing would be to start with the PX-1 as a way to start learning about pixels, basically a good stepping stone to the e682.
That is what I am doing. Going to start with two px1's and learn pixels then in a couple of years go for the e682 but for my first year I'm happy with the px1's
If you're mixing Renard boards for 'dumb' LEDs and also smart pixels, either solution will work. You can control either or both with Vixen. The PX-1 is Renard native, though the E682 can be set to output one or more banks in Renard format to your Renard boards.
I'm going with the E682 for a few reasons. It allows one ethernet cable from my computer (a Raspberry Pi with Falcon Player) to the E682, then to both smart pixels and my Renard board. You could instead have one computer output for the E682 and a separate output to the Renard stuff, but I like that the E682 handles everything. If you plan to expand in future years (you will!), I think the E682 might be the better choice.
apollosmith wrote:If you're mixing Renard boards for 'dumb' LEDs and also smart pixels, either solution will work. You can control either or both with Vixen. The PX-1 is Renard native, though the E682 can be set to output one or more banks in Renard format to your Renard boards.I'm going with the E682 for a few reasons. It allows one ethernet cable from my computer (a Raspberry Pi with Falcon Player) to the E682, then to both smart pixels and my Renard board. You could instead have one computer output for the E682 and a separate output to the Renard stuff, but I like that the E682 handles everything. If you plan to expand in future years (you will!), I think the E682 might be the better choice.
Thanks for this! I'm very tempted to go for the e682, but as the PX-1 is relatively cheap I think I might get some of these to start with, then move on to the e682 in the future. I hope I don't regret my decision!!!
