Weird Pixel Strand ...
 
Notifications
Clear all

Weird Pixel Strand problem

8 Posts
6 Users
0 Reactions
2,841 Views
bcwhitehead
Posts: 119
Topic starter
(@bcwhitehead)
Estimable Member
Joined: 15 years ago
[#34438]

I have a 65 pixel strand on my lower roofline. Its doing some thing strange. The first night it ran perfectly, then the second night the first 30 pixel ran fine. Then rest just stopped or turned all white or certain pixels just were different color. Then it would start working again for the rest of the night. Ok so third night its back to not working the way it should. It always happens around the same pixels where the rest just stop communicating. Its seems like a data issue. I have this strand on port 3 of an E6804 and have it set to reverse. However the test pattern runs fine on it. I have moved all the power cords away from it but still doesn't seem to be helping. For good measure after my show tonight I went a head and cut out the two pixel I believed could be causing this intermitnet issue. Any other advice for what could be causing this? Again it always drops the reset of the strand out around the same 3-4 pixels ( about 30pixels in). That part is consistent what the pixels do beyond those pixels is intermitent. Turn white random colors with random pixels etc. The first 30 work just fine and control just fine. I hoping the two I replaced will cure the issue. But would like to see what others have to say!

Thanks
-Brandon


7 Replies
jklingert
Posts: 1767
(@jklingert)
Noble Member
Joined: 16 years ago

What type of pixels? What voltage and how far from the controller is the first pixel? Are you doing power injection? It could be power, a bad pixel or water.


Reply
bcwhitehead
Posts: 119
Topic starter
(@bcwhitehead)
Estimable Member
Joined: 15 years ago

They are pixabulbs, 12v and from controller to first bulb is 5 to 6 feet. I am power injecting at the end of the string off the same power supply. I just find its weird how it comes and goes and always acts up around the same pixels.


Reply
Posts: 654
(@szaske)
Noble Member
Joined: 14 years ago
bcwhitehead wrote:I have a 65 pixel strand on my lower roofline. Its doing some thing strange. The first night it ran perfectly, then the second night the first 30 pixel ran fine. Then rest just stopped or turned all white or certain pixels just were different color. Then it would start working again for the rest of the night. Ok so third night its back to not working the way it should. It always happens around the same pixels where the rest just stop communicating. Its seems like a data issue. I have this strand on port 3 of an E6804 and have it set to reverse. However the test pattern runs fine on it. I have moved all the power cords away from it but still doesn't seem to be helping. For good measure after my show tonight I went a head and cut out the two pixel I believed could be causing this intermitnet issue. Any other advice for what could be causing this? Again it always drops the reset of the strand out around the same 3-4 pixels ( about 30pixels in). That part is consistent what the pixels do beyond those pixels is intermitent. Turn white random colors with random pixels etc. The first 30 work just fine and control just fine. I hoping the two I replaced will cure the issue. But would like to see what others have to say!

Thanks
-Brandon

Sounds exactly like what happened to me one time. I got moisture in one bulb and it caused chaos for the rest of the lights behind it. Changing them to strange colors or white. Once I fixed that bulb the string started working again.

-=Steve


Reply
Posts: 1115
(@11bravo)
Noble Member
Joined: 14 years ago

Moisture makes them do strange colors. The o'ring in the water proof connector some how let water pass on some of my connectors. I dried them out and taped them with electrical tape. All fine so far.


Reply
Page 1 / 2
Share: