Have you tried unicast? Try setting Vixen to unicast and put in the IP address of the AlphaPix in and see what happens.
What controllers are in front of the AlphaPix? Why start at universe 12 channel 487?
When I go from one controller to the next I like clean numbers. I would have forgot about the last 23 channels in universe 12,
skipped 13, just because, and started clean at universe 14 channel 1. That probably has nothing to do with your problem, just my 2 cents.
While I am not an AlphaPix user, I have helped others set them up. If I remember correctly the AlphaPix has a test mode that can be used to verify the pixels are connected properly and are working. Does this mode work? If not, then there is no chance that the Vixen data will work.
The internal test mode does work on the string when activated so I know the string is connected properly to the port and will light up. I've also already tried moving the string to all the other ports but no blinky other than with the test mode.
I have tried a number of other things but not yet tried unicast, so will do that next.
I have 8 DIY wifi controllers (already tested and working) that are before the megatree so that's how it started at universe 12. Then I just went with how the display setup auto-patched the channels and copied that info into the alphapix configuration right after where the wifi controllers channel assignments ended.
Seems that tonight I first have to figure out what I did to my show network. Can't get into my router now... if it's not one thing it's another... may have to reset it to factory and reconfigure it. Once I get that sorted out I can resume tearing my hair out troubleshooting the alphapix. :biggrin:
Get a program called sACNview. Use it to generate E1.31 / sACN data to send to the AlphaPix. If this works, the issue is your config on the show player. If it does not work then your issue is network or AlphaPix.
Wow, sACNview looks really interesting. I will try that out soon as I'm able to get back to troubleshooting this weekend.
What firmware version are you running?
The alphapix16 is v3|3.0|30-Mar-2016 as marked on the board below the switches.
The holidaycoro.com tech support strongly advised against trying a firmware upgrade on my own and didn't provide the file anyway when I emailed them about it. There are all sorts of warnings on their site about the dangers of performing user updates. i assume they must have had numerous incidents of update failures and didn't want to deal with the hassle unless really necessary.
BTW, I did get a chance to try unicast (setting the alphapix's IP address) and it still did nothing.
So now I'm trying to figure out how to use the sACNview software to transmit some data to the string plugged into port 1 of the board.
I finally got some light from the pixels plugged into port 1 of the alphapix. I set up sACNview using the transmit function, set to universe 12 (where the first port starts at channel 487) and entered the alphapix IP address in the unicast mode line. I clicked 'Start' and messed with the effect type settings and finally see some of the pixels lighting up! I did notice I had to reset (unplug and plug power) the alphapix to get things to work.
I guess this proves the network is doing its thing, correct?
What should my next step be? I'm not sure where to look in the Vixen setup. I've tried adding the unicast destination to the sACN config window and entering the alphapix IP address but that has not worked so far, and still doesn't do anything when set to multicast. There's got to be something staring me in the face and I'm just not seeing it.
Wait a sec. You said "AlphaPix Port 1, pixel 1 is mapped to E1.31 Universe 12 channel 487". Where are the other 486 channels going? On Vixen Setup Screen, for unicast mode, are you skipping the first 486 channels on universe 12 in your patching? If not then you have a problem there. The universe / channel info has to be the same on vixen and the controller.
