Weird AlphaPix16 pr...
 
Notifications
Clear all

Weird AlphaPix16 problem - need HELP!

38 Posts
5 Users
0 Reactions
6,449 Views
OptykMuse
Posts: 181
Topic starter
(@optykmuse)
Estimable Member
Joined: 15 years ago
[#57192]

Hey all, I've had a brand new AplhaPix16 I purchased back in 2018 and finally decided to pull it out of the box and build a pixel megatree with it as the controller, and 12 each 50 pixel strings and a tree kit I purchased. It's a really nice little controller (came with the outdoor box and 12V PS). I got a new 12-string megatree added to Vixen, added it to the E1.31 outputs, and configured the AlphaPix channels to the correct starting universes & start-channels using the display and buttons on the board. I had already connected it to the router (can't configure it until that's done anyway) and allowed a DHCP assigned IP address, which showed up on the AlphaPix's display.
I connected a pixel string to channel 1 and ran a sequence with some megatree effects added in for testing. It displayed like it should on the preview screen (starting to get excited now) and then... ZIP - NADA from the pixel string.
I went into the test mode on the AlphaPix to be sure I had the string connected right and it displayed everything in the test patterns just like it should, all pixels blazing. Went back to normal mode, still nothing from the sequence.
Ok, now here's where it gets weird... I went into the router and checked in the "connected devices" to see what showed up. I see the computer, the new AP for the wifi display props I had been fiddling with (and the pixelstick board IP), but NOT the AlphaPix. The router had given it an IP address, but it doesn't show up in the router's connected devices list. Next I opened a command line window on the computer and tried pinging the AlphaPix's address... pings just fine with normal results. Nothing I can think of will get the AlphaPix board to show up in the connected devices list even though it seems to be connected. I believe this is why nothing is displaying on the pixels when the sequence is played, although I am at a loss as to what is going on here. I've been messing with this most of today and gotten nowhere.
I also tried to get to the web browser interface by entering the assigned IP address and it doesn't come up. So there's something really weird going on between the AlphaPix16 and the router (which sees everything else just fine).
My current setup: Windows 10, a new motherboard that's plenty fast enough to run the pixel show, Firefox browser, Netgear R6120 router, tested ethernet cable, Vixen 3.9U5.

I'm hoping that the collective thought power of the community here will show me what bonehead thing I've forgotten, or failing that, what in the world is going on with the relationship between this router and the AlphaPix. I've just about scratched my hair out trying to figure this out.


37 Replies
MartinMueller2003
Posts: 7614
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

A few tings to check. If I remember correctly, the Alphapix has a browser UI. Can you access the controller via the UI? Once you have this working, please grab screenshots of the controller configuration. Post them to this thread.

In addition, get a screen shot of the E1.31 configuration on vixen for the controller and a screenshot of the start of your patching on Vixen. Most likely you have missed setting the controller name properly and then went on to miss the channel setups in the patching.


Reply
OptykMuse
Posts: 181
Topic starter
(@optykmuse)
Estimable Member
Joined: 15 years ago

Martin, I've tried a few more things today to see if I can get the AlphaPix16 working but to no avail. I've tried two other routers also just because I have them but had the same results with the AlphaPix with each one... no flashy lights and no access to the browser UI. The other two browsers at least showed the AlphaPix in the 'attached devices' list, but nothing more than that. It still responds to pings from the computer through each of the routers so has ethernet connection.
I've attached what i think are your requested screenshots...

Controller Config Screenshot
Controller Config Screenshot2
Patching (megatree start) Screenshot
Patching (PixelTree start) Screenshot

Reply
MartinMueller2003
Posts: 7614
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

You are using multicast to send data but you are using unicast to send a ping. At the moment, you are having a networking issue. If you cannot open a browser to the alphapix's ui then you cannot send data to it either. You said the alphapix got an IP from the router. I assume that is the ip address you are putting into the browser? What is that IP address?


Reply
OptykMuse
Posts: 181
Topic starter
(@optykmuse)
Estimable Member
Joined: 15 years ago

Yes, the same IP address entered on the URL line... the current AphpaPix IP address (displayed on its LCD screen) is 192.168.5.4 with the router I have it connected to.


Reply
Posts: 429
(@mikekrebs)
Reputable Member
Joined: 12 years ago

The alphapix version I have does not do multicast. But that is a Vixen thing and you are having a different problem.

Set the IP via the controls on the Alpha pix. Pick anything but what it is and of course that is within your subnet.


Reply
OptykMuse
Posts: 181
Topic starter
(@optykmuse)
Estimable Member
Joined: 15 years ago

I did try setting a different static address in the AlphaPix and then re-powered it... the router's DHCP just set the IP address to match what I had set on the AplhaPix.
I'm wondering if the multicast vs unicast is an issue with my AlphaPix... although it seems like that should have no affect on whether the browser UI would work or not.


Reply
MartinMueller2003
Posts: 7614
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

The first problem you need to fix is the networking issue. FYI: Not sure what you mean by "DCHP just set to the same value as the Static address". The AlphaPix should not trigger DHCP at all when it comes up with a static address. Also, are you sure you have set the Net Mask and Gateway properly? All three are needed to establish a proper connection.


Reply
OptykMuse
Posts: 181
Topic starter
(@optykmuse)
Estimable Member
Joined: 15 years ago

The AlphaPix16 (V3, 30March2016) I have only allows setting of DHCP on or off, the static address (if DHCP is set to off), and the net mask value. The net mask is set to 255.255.255.0 which I believe is correct.

I don't know the details of how the router DHCP process works but it is still set to DHCP and the AlphaPix (for now) is set to static. Somehow the router figures that out and uses the static IP address set in the AlphaPix and matches it in the router's IP assignment process. What I've always done in my home network router is to bind the DHCP-chosen IP addresses to the MAC addresses of select devices so they are always assigned the same IP every time the router or any device is reset in some way. It works kind of like if you assign static addresses to everything in the router but you still have the convenience of DHCP for everything else you leave unbound (the stuff I don't care what the IP address is).
I have no formal education in networking, just what I've learned over the years from the internet and of having to deal with it at work and at home.
I've run out of ideas to try with this thing so hoping someone else has had the same experience and found the cure.


Reply
OptykMuse
Posts: 181
Topic starter
(@optykmuse)
Estimable Member
Joined: 15 years ago

Something to add to the previous message...
Martin, I neglected to send one of my config screenshots, here's the 'advanced options' tab of the sACN e1.31 configuration.

Controller Config Screenshot3

These are the default settings and I was not sure of whether I needed to change anything so left it at defaults.
I also looked at the 'Destination' drop-down at the bottom of the Universes tab and only see "multicast ethernet" and "multicast local area connection" as choices. There is no unicast choice in the drop-down so don't seem to have that as a choice in Vixen. I was thinking about trying unicast but it appears I can't do that.

Also, I have not heard back from the holiday coro AlphaPix16 developer yet regarding this issue, so still awaiting that.


Reply
Page 1 / 4
Share: