Upgraded E681 help
 
Notifications
Clear all

Upgraded E681 help

20 Posts
4 Users
0 Reactions
5,236 Views
michaelc
Posts: 1540
Topic starter
(@michaelc)
Noble Member
Joined: 19 years ago
[#39810]

I am looking for help understanding the configuration of he controller. The top section lays out 7 universes plus 5 more Art-Net but the controller outputs are only 4 groups. How do you use this boards to get more universes?

Specifically, I have 12 strings of 50 count pixabulbs spread across 24 strands of a mega tree. They currently occupy the first 3 connectors for each universe group for a total of 4 universes. I want to add a Dmx output and possibly another universe of pixels. How do you configure the 4 groups to be more than 4 universes?

Sent from my iPad using Tapatalk


19 Replies
Posts: 1159
(@deonb)
Noble Member
Joined: 13 years ago

As I understand it, "the upgraded board is essentially equivalent to an E682, without the hardware '2-wire balanced' option on the E682."

But won't you need a balanced signal for your DMX output?


Reply
michaelc
Posts: 1540
Topic starter
(@michaelc)
Noble Member
Joined: 19 years ago

Actually, my end goal is to drive 300 pixels of Ws2811 5050 strips. (4 arches of 75 pixels each). If there is a way to do that using the extra capacity of the E681+ directly I'm open to that idea. The arches are about 30-40 feet from the E681+. My current setup/plans called for a KOMBY RF receiver, but I can't get it to work. I then tried the backup of using the new ESPixel stick. I'm still playing with that but having issues as well. My Plan C was direct DMX through a DMX SPI Controller like this : http://www.diyledexpress.com/index.php?main_page=product_info&cPath=29&products_id=248 . If there is a plan D that let's me connect the pixels directly to the E681+ I'm open to it. My E681+ is all 12V and my strips are 5V but I just received a Buck Converter yesterday so I could take a 12V run from the E681+ PS to the pixels if need be.


Reply
duramadmax
Posts: 904
(@duramadmax)
Noble Member
Joined: 16 years ago

I run two e681.5's as I call them. They will span universes on each cluster. Just put your total pixels string length in each cluster and it will span multiple universes.


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

I have five upgraded E681's (I call them E681-12's) - they configure the same as the E682's. If you need balanced outputs, I created a plug-in board to provide a true RS-485 output from it and has jumpers for DMX or Renard pinouts. I still have a couple left if interested. You mentioned Art-Net - really the options are E1.31/UniCast (12U) OR E1.31/Multicast (7U) OR Art-Net (12U). There's not a lot of call for Art-Net but I tested it briefly with Madrix or Glediator as I recall.


Reply
michaelc
Posts: 1540
Topic starter
(@michaelc)
Noble Member
Joined: 19 years ago

Before I go messing up my configuration, does the attached look like what I'm describing. Assuming the existing 12 ports are collapsed an contain 50 pixels nodes each and the new arches are 150 pixels each.

Capture

Reply
duramadmax
Posts: 904
(@duramadmax)
Noble Member
Joined: 16 years ago

Your channels numbering is all off on your spreadsheet. Grab a screen shot of the e681 setup page and lets compare


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

The E682 calculates the ending channels usually - as mentioned though, your sheet doesn't add up. You have 200 (4x50) pixels/cluster and a universe is 170 leaving 30 for the next universe so it would end at channel 90. So it would start at 100/1 and end at 101/90 if I did my 'cipherin' right... That should add up to 600 (510 + 90) channels or 200 pixels...


Reply
michaelc
Posts: 1540
Topic starter
(@michaelc)
Noble Member
Joined: 19 years ago

So if I interpret, you have to assume you are using up the entire universe before it assigns the next universe. In essence a string has to span universes. So my third string which ends at 100/450 has to immediately be followed by my fourth string which now starts at 100/451, fills up 100, spans to 101/90. So it would seem I have to make changes in xl to break up my strings to span universes. That's the part I didn't understand. It Would seem you have to pack a universe before using the next which is not the assumption used currently when assigning ports.

Sent from my iPad using Tapatalk


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

XLights doesn't know or care about controller limits - it uses logical channel numbering as you enter universes for the E1.31 entries. The key is to ensure you encompass what you have set on your controllers.


Reply
Page 1 / 2
Share: