Technicolor quality...
 
Notifications
Clear all

Technicolor quality?

256 Posts
45 Users
0 Reactions
83.4 K Views
Posts: 95
(@danolgb)
Estimable Member
Joined: 17 years ago
timon wrote:Park, as in Anahiem?

Yes. Also, I'll ask my Tech Services friends about the Fire Marshal. I'm also friends with one of their Senior Pyros. I got to be on her crew for the Manhattan Beach Christmas Fireworks this year. She does that show and another on the side.


Reply
timon
Posts: 2149
(@timon)
Noble Member
Joined: 16 years ago

I assume that show cost a few thousand to put on. I get a kick that each show at Disneyland cost over $15K. I'd love to see their launchers since I understand that they are air pressure driven and the in many cases there is a microprocessor in the shells to set them off.

I sure hope they have the Technical Conference at Disney again later this year ($900). My wife gave me the go ahead but they were sold out for last year by the time I found out about it. I'm on the mailing list now so we'll see.


Reply
Posts: 928
(@arw01)
Noble Member
Joined: 13 years ago

Besides a bucket, get a mister going on the garden hose, it seemed from reports, that the slightest amount of moisture in the air did them in, and I am sure many a technicolor was put in a bucket at testing time. Would be good to get a strong fan too so that they wires flex with each sweep of the fan head driving the mist..

And in full sun too, as some of the solar gain might be an influence in plastic around the wires failing to seal.


Reply
Posts: 843
(@captainmurdoch)
Prominent Member
Joined: 14 years ago

And not just a burn in but periods of burn with periods of dark (and potentially no power at all) in between so you can see if the heating and cooling cycles expose flaws or cracks in the armor allowing water in. 38 hours of burn in isn't the same as 48 hours in the yard unless the yard lights stay on 24x7.


Reply
Posts: 23
(@hauvega)
Eminent Member
Joined: 18 years ago

Disassemble one of them to see the construction of the pixel. Want to know if there is any conformal coating on the pcb and terminations.


Reply
Posts: 419
(@txag2008)
Honorable Member
Joined: 17 years ago

What concerns me is that I watched a video of Technicolors v1 tested in water and even frozen in ice and the pixels still worked fine. I don't think any actual users had this type of success though.


Reply
Posts: 853
(@roterhead)
Prominent Member
Joined: 15 years ago
timon wrote:I assume that show cost a few thousand to put on. I get a kick that each show at Disneyland cost over $15K. I'd love to see their launchers since I understand that they are air pressure driven and the in many cases there is a microprocessor in the shells to set them off.

I sure hope they have the Technical Conference at Disney again later this year ($900). My wife gave me the go ahead but they were sold out for last year by the time I found out about it. I'm on the mailing list now so we'll see.

Curious. What subjects does the conference cover?


Reply
timon
Posts: 2149
(@timon)
Noble Member
Joined: 16 years ago

Oh it went over just about everything you could image when doing automated shows. As i said it covered WOC, The fireworks show, Fantasmic and several others. They were going over the Glow with the Show ears, have meetings with the designers and producers of the shows and it was all at the technical level. On top of that tours of the control areas. I suspect it would have been Disney Technical nirvana.

Here is the link to what they put on. http://livedesignonline.com/news/disney-technical-training-anaheim-december-3-4

---------------------------------------

Got the updated Technicolor pixels this morning.

First impressions:

  • The material seems to be a bit softer that before. One thing I had talk to Ray about was checking the compatibility of the plastic uses to mold the pixels and the wire used. My thoughts were that if they were too different then you may not get a complete seal. I suggested that he consult with a plastic guru and make sure the plastics would seal tightly. I ask Ray about this the next time we talk.
  • Conformal coating. I've not opened any of the pixels up but when they are coated you also coat the wire trying to not go so far that the coated wire extends outside the pixel body. Well, it turned out that a couple of them pixels has the conformal coating past the pixel body so I know that they were coated. BTW, if some gets past the body it's not a technical problem but it is a aesthetic one.
  • General build. The general build looks good other than a little over spray of the conformal coating. I did find one spot where a lead wire had a small cut in the insulation. It looks as if it was done when the wire leads were being stripped as if the wire was slid over the blades. I only found this on the exit pigtail so it could have been done by the manufacture that makes the tails. Again I will talk with Ray and see if he can find out what may have happened.
  • Initial power up. The pixels powered up just fine and are now running a #11 test on my E682.

I'm going to put together a test sequence in HLS that will run the pixels through a series of tests. One of the test will keep the pixels at full ON for at least an hour then a series of color tests then back to full on.

If anyone has some specific tests you would like run let me know and I'll program them in.

After the initial tests I'll run some that Steve suggested plus a few stress test of my own.


Reply
tucsonlights
Posts: 667
(@tucsonlights)
Honorable Member
Joined: 15 years ago

Timon,
So once you have tested the TC pixels and are happy with them, will Ray ID them on his site so we know which ones are the improved versions?


Reply
Posts: 14
(@keitha43)
Active Member
Joined: 16 years ago

I suggest outside real world testing in rain while weather is still cold for more realistic testing after indoor testing is done.


Reply
Page 17 / 26
Share: