Thought I'd share some info on this product on here, since I didn't find anything. Also the included 'manual' tells you very little.
Essentially it receives DMX and has 5 x PWM open collector terminals and 1 universe worth of 'pixel' data output. The controller can be configured for various pixel types, I'm using standard WS2811 RGB pixels in my case. Input voltage range is 5->24V
DMX start channel is software set from the menu
When DMX is not connected the unit can output one of 100 patterns, each of which offers 10 levels of speed control. The moment DMX is detected the SP2101E switches into DMX mode.
One slightly disappointing aspect is I was hoping the channels would be more configurable, the issue being that the first 5 assigned channels (based on the DMX start channel) are shared between the 5 x PWM connections, so you can't control these channels independently from the pixels. I think the solution would be to install some 'null pixels' so a couple of WS2811 ICs with or without their LEDs. In that way the PWM channels start on the DMX receive channel (say 1) and the pixels start on receive channel + 6 (say 7)
In the pic below I've connected a white LED and associated resistor to PWM output 1, and a length of WS2811 5V strip. I'm outputting 255 on channels 1 and 7, so the LED lights (channel 1), and the green component of pixels 1 and 3 (channels 1 and 7). Also note in DMX mode the display on the SP201E shows the configured pixel type.
Hope this is of use to anyone looking to drive (up to) a universe of 'pixel' devices (or similar) from DMX data. My plan is to integrate some addressable festoon lighting (which i have) into my garden DMX universe. It only needs 45 channels.
So i in order to bypass the first 5 channels (well 6 actually since I'm using two ICs) so I can use the PWM outputs independently from the pixels, I built a 'null pixel' circuit, which is basically this:
The value of R1 is 3K3 which should give about the right voltage across the IC, I also included the 33 ohm resistors on the data lines.
And yes - soldering the surface mount ICs was a b*tch, but I have tested all the connections and it seems good.
Having trouble making it work - does anyone know how these handle having the R, G, B pins unconnected? Could this be an issue? For clarity, I don't intend to drive anything from these ICs, these are simply to 'use up' the channels.
Thanks
Update - I checked it out with the oscilloscope. The board is doing what it should i.e. the output is the same as the input but missing the first 6 channels. I think the issue may be to do with the mixture of ICs I am using. The board has WS2811 ICs (as marked on the chips), but the 12V strip I am connecting to for testing has chips marked GS1903. I believe the timing specs may be slightly different between the two, so mixing the two chips may be causing issues? Connecting the 12V strip directly to the controller it works OK, but mixing the chips in the WS2811 'chain' seems to be causing issues.
So it IS okay to leave the R,G,B pins disconnected. That wasn't the issue.
I tried connecting a single GS1903 IC before the 12V strip, and it worked correctly. The good news is the 12V 'festoon' lights I am looking to drive have chips marked WS2811 in them (not GS1903) so may actually be compatible.
What exactly is the relationship between the DMX universe and the pixels? i.e. does it literally only support 170 pixels, since that is all a single universe can accommodate? Or are those built-in patterns accessible via DMX? I can't quite figure out the $30 price tag.
It's a slightly weird device TBH. I think many users would use the preset patterns - not sure of the number of pixels / channels but believe it's more than you get from DMX. If using the DMX input then yes using RGB lights that means 170 'devices' only. That's fine for some applications like floods or festoon lighting applications though (which is my use case)
A logical upgrade would be able to select patterns via DMX commands, but that's not supported. As mentioned above if I'd designed it I would also have separated the PWM outputs from the Pixel channel outputs.
I didn't pay 30USD for mine, even with the crap value of the UK pound.


