Has anyone tested this Strip ?
Apparently this strip is equivalent to Apa102 .
I have a strip of apa102 144 Pixels/m on the way from China with a supporting controller .
I am a bit concerned that the ws 2812b 60 pixels/meter won't be sufficient for optimum video .
Hi, a P10 would be 100 / Meter & a HD TV 1080 / Meter (at 56" screen size). It all comes down to viewing distance.
It would be usefull if we could compile some examples - spacing v viewing distance.
Barnabybear wrote:Hi, a P10 would be 100 / Meter & a HD TV 1080 / Meter (at 56" screen size). It all comes down to viewing distance.
It would be usefull if we could compile some examples - spacing v viewing distance.
I have been experimenting with resolution for 3yrs now with strings and they are a no go , unless one builds a huge matrix and stand 3 blocks away to view it .
Strip is the way to go and I am leaning towards 144 pixels/m for optimum resolution from 0 to 150 ft away .
I am not concerned about any further distance than that or my neighbors may be watching my screen throughout their homes . 🙂
Hi, I have some 144 / Meter. The 5050 leds are 7mm spaced along the strip / tape but the tape its self is 12mm wide (IP rated will be wider), so your not going to get an equal horizontal / vertical spacing. I'm guessing that thats why the 66 / Meter came about with a 15mm spacing, as with IP silicon tube that proberbly as close as you can get two strips and keep a horizontal / vertical ratio of 1:1.
There's some that get paid a lot more than we do to come up with this info.
https://www.christiedigital.com/en-us/digital-signage/visual-display-technology/resources/LED-displays
http://www.daktronics.com/en-us/learning-and-resources/led-learning-center
--Jon Chuchla--
Sent from my iPhone using Tapatalk
jchuchla wrote:There's some that get paid a lot more than we do to come up with this info.
https://www.christiedigital.com/en-us/digital-signage/visual-display-technology/resources/LED-displayshttp://www.daktronics.com/en-us/learning-and-resources/led-learning-center
--Jon Chuchla--
Sent from my iPhone using Tapatalk
A 4k TV would suffice 🙂
I am avoiding the jumbo tron look of P style panels and the current process to control them .Not to mention weather proofing them and so on.
Pixel strip at 144/m would be quite exceptional irrespective of 1:1 spacing i believe .
Hi, there is a nice write up on the Apa102 protocol in this blog that my be of use to anyone wanting to build their own controller.
Should be quite easy to do with an ESP8266 (not 01 as the SPI pins arn't broken out would need to be something like a 12, unless some has come up with a way to bitbang on GPIO's 0 and 2).
// SPI setup - 4Mhz - MSB first - clock high at rest and send data on low
SPI.beginTransaction(SPISettings(4000000, MSBFIRST, SPI_MODE2));
// start frame
SPI.transfer(0x00);
SPI.transfer(0x00);
SPI.transfer(0x00);
SPI.transfer(0x00);
// LED frame
SPI.transfer(0xff); // 0xff - unless global dimming is required
SPI.transfer(<blue value>);
SPI.transfer(<green value>);
SPI.transfer(<red value>); // repeat LED frame for number of pixels
// end frame
SPI.transfer(0xff); // send once for every 16 pixels
jchuchla wrote:There's some that get paid a lot more than we do to come up with this info.
https://www.christiedigital.com/en-us/digital-signage/visual-display-technology/resources/LED-displayshttp://www.daktronics.com/en-us/learning-and-resources/led-learning-center
Well Jon, they may get paid more than we do (since I am not making anything right now that is not saying much - :omg:) but I bet they don't have near as much fun as we do with this stuff!
Good information though at any rate for the "tinkers" in us.
Thanks for sharing.
Bill
Barnabybear wrote:Hi, there is a nice write up on the Apa102 protocol in this blog that my be of use to anyone wanting to build their own controller.
I have been playing with APA104 strip for close to a year now as well as APA106 nodes. I wish I had the test equipment to get good measurements on the data line so that I could make more accurate findings. I do see that they "appear" to run just fine with my J1Sys P2 controller that I use to drive them though but can't really say as to how far they can be pushed for speed or distance as I have yet to try and really test them hard.
i have used SK9822 ledstrip , i have same function as APA102 LED , for project , it is better to use SK9822 and apa102 rather than ws2812b , as SK9822 have clock and data.
this is the datasheet of sk9822 led , may be it will help you .
http://www.szledcolor.com/download/SK9822%20LED.pdf
