Sandevices Controll...
 
Notifications
Clear all

Sandevices Controllers

12 Posts
4 Users
0 Reactions
3,497 Views
pmiller
Posts: 2795
Topic starter
(@pmiller)
Famed Member
Joined: 12 years ago
[#50017]

Before last night I was getting sequence errors but they were limited to 6-7 maximum over a 5 hour period. Now I'm getting 90-100-120 and even higher sequence errors. My show seems to be running properly but I'm concerned about the sequence errors. I'm running my show using FPP 2.5.2. This morning I ran a sequence through Vixen and was getting the same results so I pretty much eliminated it being a FPP issue.
One other thing. I have 8 snowflakes with 48 pixels each. The 682 is driving 2 snowflakes from one output for a total of 96 pixels, 12 volts at 25% output. Snowflake 1 looked good as did all the other snowflakes but snowflake 2 was acting weird. When the show was over for the night a few pixels on snowflake 2 were still flashing. Went downstairs and tripped the breaker and then turned it back on. Strange but a few pixels were still flashing on snowflake 2. Went back downstairs and tripped the breaker off for the night. Is there a possibility of residual voltage going to that snowflake for a few pixels to even come on when no data is sent to it?

Sent from my SM-T710 using Tapatalk


11 Replies
Posts: 740
(@ezellner)
Prominent Member
Joined: 11 years ago
pmiller wrote:Before last night I was getting sequence errors but they were limited to 6-7 maximum over a 5 hour period. Now I'm getting 90-100-120 and even higher sequence errors. My show seems to be running properly but I'm concerned about the sequence errors. I'm running my show using FPP 2.5.2. This morning I ran a sequence through Vixen and was getting the same results so I pretty much eliminated it being a FPP issue.
One other thing. I have 8 snowflakes with 48 pixels each. The 682 is driving 2 snowflakes from one output for a total of 96 pixels, 12 volts at 25% output. Snowflake 1 looked good as did all the other snowflakes but snowflake 2 was acting weird. When the show was over for the night a few pixels on snowflake 2 were still flashing. Went downstairs and tripped the breaker and then turned it back on. Strange but a few pixels were still flashing on snowflake 2. Went back downstairs and tripped the breaker off for the night. Is there a possibility of residual voltage going to that snowflake for a few pixels to even come on when no data is sent to it?

Sent from my SM-T710 using Tapatalk

Coincidentally, I added six snowflakes this year (174 pixels each). Each group of three is powered by a separate power supply and attached to a separate E682 (each snowflake to its own output). The E682 also are driving other pixels without issue. I also had that similar residual twinkling on a couple of my snowflakes along with odd flashing occasionally during running sequences. These older E682s are running 270 ohm resistor networks at the outputs. My newer E682 came with 150 ohm resistor networks so I thought I'd replace the output resistors on the suspect snowflake outputs (one resistor covers two outputs). I had one extra to try and it seemed to clear up one of my problem snowflakes. I ordered more so I could see if it took care of the others. Just got done installing them so I'll see tonight if it was 100% successful. I'm confident power is not an issue but my data runs are on the longer side (20 to 35 feet). I figured the data signal needed a boost. YMMV


Reply
Posts: 20
(@joshuagray)
Eminent Member
Joined: 16 years ago

Pat, I have noticed that when a sequence is running if I refresh the page on a controller the errors go way up. If I refresh after the sequence only a couple of errors show up. Also with all the rain we have had I also had an issue like that and I actually had to go out and disconnect a couple of connections and plug them back in. Just 2 vertical connections that seemed dry but it did fix the issue.


Reply
Posts: 2048
(@scootchu)
Noble Member
Joined: 17 years ago
pmiller wrote:Before last night I was getting sequence errors but they were limited to 6-7 maximum over a 5 hour period. Now I'm getting 90-100-120 and even higher sequence errors. My show seems to be running properly but I'm concerned about the sequence errors. I'm running my show using FPP 2.5.2. This morning I ran a sequence through Vixen and was getting the same results so I pretty much eliminated it being a FPP issue.
One other thing. I have 8 snowflakes with 48 pixels each. The 682 is driving 2 snowflakes from one output for a total of 96 pixels, 12 volts at 25% output. Snowflake 1 looked good as did all the other snowflakes but snowflake 2 was acting weird. When the show was over for the night a few pixels on snowflake 2 were still flashing. Went downstairs and tripped the breaker and then turned it back on. Strange but a few pixels were still flashing on snowflake 2. Went back downstairs and tripped the breaker off for the night. Is there a possibility of residual voltage going to that snowflake for a few pixels to even come on when no data is sent to it?

Sent from my SM-T710 using Tapatalk

I had a Chroma bulb, a pixel tree and a mini matrix do that. It was water in the connector. Also a bad ground will make the random twinkling or water.


Reply
pmiller
Posts: 2795
Topic starter
(@pmiller)
Famed Member
Joined: 12 years ago

I have waterproof connectors and all my controllers are covered by garbage cans so no connections can get wet. Guess I'll unplug the line going to the first snowflake and then from the first to second and replug to see if that solves the problem. Never had this problem before. Thanks guys.

Sent from my SM-T710 using Tapatalk


Reply
pmiller
Posts: 2795
Topic starter
(@pmiller)
Famed Member
Joined: 12 years ago
ezellner wrote:Coincidentally, I added six snowflakes this year (174 pixels each). Each group of three is powered by a separate power supply and attached to a separate E682 (each snowflake to its own output). The E682 also are driving other pixels without issue. I also had that similar residual twinkling on a couple of my snowflakes along with odd flashing occasionally during running sequences. These older E682s are running 270 ohm resistor networks at the outputs. My newer E682 came with 150 ohm resistor networks so I thought I'd replace the output resistors on the suspect snowflake outputs (one resistor covers two outputs). I had one extra to try and it seemed to clear up one of my problem snowflakes. I ordered more so I could see if it took care of the others. Just got done installing them so I'll see tonight if it was 100% successful. I'm confident power is not an issue but my data runs are on the longer side (20 to 35 feet). I figured the data signal needed a boost. YMMV

Let me know if changing the resistors worked. That odd flashing also occurred during sequence running. Didn't happen all the time. It seemed to clear up but when show was over the same pixels randomly twinkled. Strange thing was I turned off the power at the breaker and then when I turned the breaker back on they were still twinkling. That's when I powered down for the night.

Sent from my SM-T710 using Tapatalk


Reply
Posts: 740
(@ezellner)
Prominent Member
Joined: 11 years ago

I have no flashing pixels when no sequence is running after installing the new resistor networks but I still have one snowflake that flashes wrong colors every now and then during a sequence. Just got done checking voltages and every connection. Last thing to check is my data line connection at the E682. There could be a stray strand of wire from either power or ground that is messing me up but I can't check that until daylight.


Reply
pmiller
Posts: 2795
Topic starter
(@pmiller)
Famed Member
Joined: 12 years ago
ezellner wrote:I have no flashing pixels when no sequence is running after installing the new resistor networks but I still have one snowflake that flashes wrong colors every now and then during a sequence. Just got done checking voltages and every connection. Last thing to check is my data line connection at the E682. There could be a stray strand of wire from either power or ground that is messing me up but I can't check that until daylight.

Tonight everything seems to be running good. I update to FPP 2.5.3. I still get sequence errors but not as many as last night.

Sent from my SM-T710 using Tapatalk


Reply
pmiller
Posts: 2795
Topic starter
(@pmiller)
Famed Member
Joined: 12 years ago

I was running good until now. Notice the weird pixel stuff going on the second snowflake from the right.

Sent from my SM-T710 using Tapatalk


Reply
pmiller
Posts: 2795
Topic starter
(@pmiller)
Famed Member
Joined: 12 years ago

I think it's a signal issue. I switched around the connections and made snowflake #2 the input and the output from #2 to #1. #1 acted funny. I reset the connections at the snowflakes and it seems to have cleared up. We will see.

Sent from my SM-T710 using Tapatalk


Reply
Page 1 / 2
Share: