Notifications
Clear all

Roofline pixels

39 Posts
17 Users
0 Reactions
13.7 K Views
jchuchla
Posts: 8698
(@jchuchla)
Illustrious Member
Joined: 15 years ago

Regarding the shape. The pixabulb/brilliant bulb is almost exactly the same diameter as a c9, but its height is only the height of a c7. So they're short and fat.
The strawberry lens shape of the pixabulb makes for a more even light distribution in the lens. The c9 covers in an 8mm mode are much brighter at the base near the led than the end of the bulb. The strawberry bulb is much more evenly distributed comparatively speaking. This really only matters when looking at it from the side. If looking at it top down, they look the same.

Sent from my iPhone using Tapatalk Pro


Reply
Posts: 598
(@nutz4lights)
Honorable Member
Joined: 17 years ago
jchuchla wrote:The strawberry lens shape of the pixabulb makes for a more even light distribution in the lens. The c9 covers in an 8mm mode are much brighter at the base near the led than the end of the bulb. The strawberry bulb is much more evenly distributed comparatively speaking.

I very respectfully disagree. If you look at the picture i posted on the previous page, it seems to me that, yes, the technicolor has a bright short height burst ring at the very bottom, but the color is much more uniform and consistent up the full height of the bulb. The picture shows pixabulb and technicolor in one picture which is a great way to compare apples to apples. The pixabulbs in that picture are all over the place in regards to brightness and color distribution showing far more hot spotting to my eye.

Like you said, though, if you don't aim them up (there is a local guy that aims them at the viewer) you won't be able to tell a difference. I aim mine up. I had that 30 foot section in the video up for several months over the summer and i just had to have the technicolor for bulb height and color uniformity.

Louie

Sent from my SM-G928V using Tapatalk


Reply
Posts: 55
(@b0nafide)
Trusted Member
Joined: 10 years ago
jpb wrote:For the last 4 Christmas' I have used 2801 5V bullet nodes with C9 covers over them with zero failures. Pictures tell the story but the lights are inside square ducting with holes drilled for a friction fit of the C9 covers. I have them below my gutters as pictured and on the gable ends and ridge.

Can you expand on the square ducting? That is a very clean setup!

I see you've used zip tie mounts under your gutters then zip tied the ducting to the mount. Did you screw in the mounts or are they just stickered?

Love that look. Gives me a few ideas.

What bulb covers did you use? Where did you get them? What size of hole did you drill. I really like your setup ... it's uber water resistant!

Sent from my iPhone using Tapatalk


Reply
Posts: 556
 jpb
(@jpb)
Honorable Member
Joined: 19 years ago
b0nafide wrote:Can you expand on the square ducting? That is a very clean setup!

I see you've used zip tie mounts under your gutters then zip tied the ducting to the mount. Did you screw in the mounts or are they just stickered?

Love that look. Gives me a few ideas.

What bulb covers did you use? Where did you get them? What size of hole did you drill. I really like your setup ... it's uber water resistant!

Sent from my iPhone using Tapatalk

The ducting is 25mm / 1" with spacing between pixels of 45mm. The spacing came about because that is the spacing that comfortably works with strings I had (50mm / 2").

I drilled the holes with a standard twist drill to around 10 to 12mm and then used a tapered reamer to take them to the correct size. Using a 15mm or so drill from the outset was causing too much tear out and resulting in a loose fit but by drilling undersize and then using the reamer it was a more gradual process and gave neater and tighter holes.

I did try to use stick on cable tie mounts under the gutter but in the hot Australian Summer the glue was softening and the cable tie mount falling off. I guess I could have tried a black construction adhesive but I ended up using two long cable ties joined together right around the gutter. I can poke the tie up from the bottom between the gutter and the fascia and then with a bit of a jiggle make it pop out from under the roof tile so I can grab the end. Going the adhesive method I would need to ensure that the one I used would stick to bother the metal gutter and the plastic cable tie mount, and not ooze into the body of the mount and block the holes that the cable tie goes through.

A word of warning, you need to keep the ducting fairly straight while installing it or moving it around because it becomes a bit fragile with the all the holes drilled in it. I get my teenage kids to help put it up and take it down so that the longer lengths are supported in three places.

The pixels I am using look like these but are 2801 and a 50mm spacing
https://www.aliexpress.com/store/product/50pcs-DC5V-12mm-WS2811-led-smart-pixel-node-with-all-color-wire-20AWG-IP68-rated/701799_1932874154.html?spm=2114.12010612.0.0.FdsGnJ

And the covers are also from Ray Wu
https://www.aliexpress.com/item/faceted-White-C9-lens-cover-100pcs-set/32474486311.html?spm=2114.01010208.8.54.STGvzl

The covers are quite heavy and bulky so the shipping cost is a killer. One of the fellas down here is printing his own on a 3D printer and making them cheaper than purchase and shipping costs.

Jon


Reply
Posts: 125
(@northernwarrior)
Estimable Member
Joined: 10 years ago
jpb wrote:For the last 4 Christmas' I have used 2801 5V bullet nodes with C9 covers over them with zero failures. Pictures tell the story but the lights are inside square ducting with holes drilled for a friction fit of the C9 covers. I have them below my gutters as pictured and on the gable ends and ridge.
And then they are stored on the ceiling of the garage in the off season..

Jon

Wow - this is exactly what I am looking for. what and where do you find square ducting ? this is a very clean look. can you explain a little more in detail how you attached it below your gutter ?


Reply
Page 6 / 8
Share: