Notifications
Clear all

Roofline pixels

39 Posts
17 Users
0 Reactions
13.7 K Views
Posts: 556
 jpb
(@jpb)
Honorable Member
Joined: 19 years ago
northernwarrior wrote:Wow - this is exactly what I am looking for. what and where do you find square ducting ? this is a very clean look. can you explain a little more in detail how you attached it below your gutter ?

You should be able to get the square ducting from an electrical supplies place. I know this place wont be in your neck of the woods but here is an example
http://www.rexel.com.au/products/CONDUIT-ELECTRICAL-PVC-25-X-25MM-GREY-C-W-LID_CD2525GR_753631.html

I originally planned to use sticky cable tie mounts under the gutter as in the second picture but I found that on hot days the glue was softening and the mounts falling off. Perhaps this kind of mount in picture 1 with a screw through the middle into the fascia as indicated by the yellow arrow would work. For me, this is above the path leading to the front door so any solution must be neat and unobtrusive for the other 11 months of the year.

The third picture shows how I am currently holding them up with a long cable tie (two shorter ones joined) right around the gutter. This works for me but it all depends on whether or not you can poke a cable tie between the gutter and fascia and then get it to come out from under the roof sheeting ( tiles for me ).

Cable Tie Mount
20170129 153925
20170129 154724

Reply
Posts: 125
(@northernwarrior)
Estimable Member
Joined: 10 years ago

That looks very cool. I can't seem to find anything similar here in canada. I'll keep searching. 🙂

Quick question for anyone
If I want to start small and figure out if I want strips or nodes is it OK to run just a couple strips with a 12v 350w 30a power supply ? I want to get a large enough power supply so I can power it all once I decide.

Is it possible or is it too large to run just a couple strips ?

Sent from my SM-G386W using Tapatalk


Reply
Posts: 55
(@b0nafide)
Trusted Member
Joined: 10 years ago
northernwarrior wrote:That looks very cool. I can't seem to find anything similar here in canada. I'll keep searching. 🙂

Quick question for anyone
If I want to start small and figure out if I want strips or nodes is it OK to run just a couple strips with a 12v 350w 30a power supply ? I want to get a large enough power supply so I can power it all once I decide.

Is it possible or is it too large to run just a couple strips ?

I don't think it's too much but I stand to be corrected.

Where are you in Canada? I'm near Edmonton.

I decided to go with bullet pixels instead of strips... people seem to have more weatherproofing luck with bullets over all others - obviously important for us.

Thanks for following up on that square ducting. That is by far the cleanest solution I've seen.

Sent from my iPhone using Tapatalk


Reply
Posts: 125
(@northernwarrior)
Estimable Member
Joined: 10 years ago

I am in Ottawa and I think I'm going to go with bullets as well. Question though : do all of them come with little cuts in the sleeve so you can push them through say metal and it stays ?

Where did you get yours ? Maybe you can search for the square ducting as well. I'd love to try this out. I don't think I'd use the c9 covers , I just want the node showing. More stealthy 🙂

Sent from my SM-G386W using Tapatalk


Reply
Posts: 55
(@b0nafide)
Trusted Member
Joined: 10 years ago

I don't know about the cuts... this is my first year as well.

I pre-ordered from DIYLEDEXPRESS. For us Canadians they seem like the best place to shop.. However expect to pay an arm and a leg for shipping. I looked at HolidayCoro but they ship via UPS and I know from past experiences UPS tacks on an extra in house "customs charge" which is unnecessary and it drives me apeshit.

I agree on the c9 covers. I went to pixels for a reason... My house doesn't need to look traditional anymore 🙂


Reply
Page 7 / 8
Share: