Replacing a bad pix...
 
Notifications
Clear all

Replacing a bad pixel quickly?

25 Posts
10 Users
0 Reactions
7,041 Views
Posts: 130
Topic starter
(@waynekremer)
Estimable Member
Joined: 14 years ago
[#43272]

I'm curious as to how everyone replaces a bad pixel. I cut the bad pixel out and solder in a new one, but that requires 6 solder points and 6 heat shrink tubing...and that stinks when you are out in the cold. I've seen the solder tubes, but those look big to me and you'll see them stand out. Is there a better way?


24 Replies
Wolfie
Posts: 2225
(@wolfie)
Noble Member
Joined: 11 years ago

I bought 150 no crimp blue butt connectors off ebay for $30. Use those. They include solder inside and are heat shrink outside. Only need a heat gun (hobby lobby embroidery heat gun) and wire strippers. 5 minute job and you are back inside.

These are from a completely different vendor but same basic product:
http://www.ebay.com/itm/381845178792

You CAN cut them shorter. They are optically translucent and end up virtually invisible. If someone can see these, then they are in the middle of your display.


Reply
Posts: 8517
Wolfie
Posts: 2225
(@wolfie)
Noble Member
Joined: 11 years ago

The problem with those is they shorten the pixel wire a lot more (may be an issue with 4" pixel spacing on trees and such) and they stick out 90 deg from the wire lay. The inline butt connectors do neither. Well, they do shorten it slightly but very little, if you have less than 1/8" play in wire, you are doing something wrong.


Reply
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago
Wolfie wrote:The problem with those is they shorten the pixel wire a lot more (may be an issue with 4" pixel spacing on trees and such) and they stick out 90 deg from the wire lay. The inline butt connectors do neither. Well, they do shorten it slightly but very little, if you have less than 1/8" play in wire, you are doing something wrong.

he asked for quickly 🙂 there is no quicker way than thumb press wire splices .
When its pouring rain or freezing cold , who really cares about spacing ?

Just make certain that you allow enough wire on the replacement pixel to compensate , a no brain'r really .


Reply
Posts: 297
(@1983ss454)
Reputable Member
Joined: 16 years ago
angus40 wrote:he asked for quickly 🙂 there is no quicker way than thumb press wire splices .
When its pouring rain or freezing cold , who really cares about spacing ?

Just make certain that you allow enough wire on the replacement pixel to compensate , a no brain'r really .

Those are 2 of the big positives on my list of moving from Massachusetts to Florida this past year lol. I used to just cut, strip, put them together and electrical tape till the next day lol

Sent from my iPhone using Tapatalk


Reply
Posts: 130
Topic starter
(@waynekremer)
Estimable Member
Joined: 14 years ago

Wow...I see an opportunity for someone here to make $$$. Create a waterproof thumb press inline wire splice. One that has 3 wires and another for 4 wires. No heat gun would be required.

Thanks for the options guys...


Reply
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago
WayneKremer wrote:Wow...I see an opportunity for someone here to make $$$. Create a waterproof thumb press inline wire splice. One that has 3 wires and another for 4 wires. No heat gun would be required.

Thanks for the options guys...

Thumb press connectors are dirt cheap already . 🙂
I live in the rain belt and have only had to do 1 pixel repair on my mega tree in 4 yrs .
These little gems solved the issue for me until seasons end when I could do a proper solder and heat shrink repair .
As Wolfie stated these hang out at an angle and look goofy cosmetically .


Reply
Wolfie
Posts: 2225
(@wolfie)
Noble Member
Joined: 11 years ago

Yea, spose thats a valid point 🙂

But, I don't plan to be fixing pixels out in the weather anyway. I planned ahead 🙂

My window frames just hook on and come down in like 3sec.
My eve pixels are in sections with pigtails on each end and just hang on 3D printed clips off the gutters. Up and down the ladder in a couple minutes max.
My singing bulbs are PVC over rebar so they lift off in zero time.
My spider web/spinner is also PVC over rebar so it too lifts off in zero time.
My arches simply stake in place and the bars that are staked aren't glued so pop 3 off and take it inside.
My tree will be on an ASAP and strips with Delphi connectors on each end of the strands so simply lower it down, unplug a strip (top and bottom) plug in the backup and jack it back in place. Take the dead strand in the warm basement for repairs.
My floods each disconnect with 1 pigtail and are either on stands or clips on the gutter, again zero time (I have a 4p pigtail with a null pixel to plug in while I am repairing the flood).
My FM/Pi/Router has one 12v wire with clip and is on a H stand so it comes inside in seconds.
My controller box is fully pigtailed and on a movable PVC stand, again under a minute outdoors and I have another falcon and PSU already mounted on the same mounting plate so I simply swap out the whole plate and put the box out with a quick settings upload.
My PSU boxes are also wired with disconnects and can be removed in under a minute outdoors.

There is nothing that requires me to be out in Wisconsin winter more than a couple minutes to replace pixels in or otherwise repair. Everything can be repaired quickly and easily bringing it indoors. The only element I can't get in the basement is the 4' web/spinner but it can go in the garage with a torpedo heater so I am out of the elements fixing that as well. Not as warm as the basement but better than fighting 20 below with snow drifts.


Reply
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago

I see . Things change if you have a pixel string tree , especially with certain pixels .

best of luck to the OP should he have the need to repair in adverse weather .


Reply
Page 1 / 3
Share: