question about sett...
 
Notifications
Clear all

question about setting up a second E682

30 Posts
7 Users
0 Reactions
16.4 K Views
Posts: 3735
(@algerdes)
Famed Member
Joined: 15 years ago

At least you have a small yard to practice on. Some were thrown into the deep end of the pool on the first outing! :omg:


Reply
pmiller
Posts: 2795
(@pmiller)
Famed Member
Joined: 12 years ago

Jim at Sandevices was supposed to be working on getting more universes out of the 682 but that was a couple years ago. Haven't hear anything about it since then.

Sent from my SM-T710 using Tapatalk


Reply
Posts: 247
Topic starter
(@bcer960)
Reputable Member
Joined: 10 years ago

Ok, finally getting to setting the second E682. Just lots of small stuff to clean up on the other elements before starting something new.

Anyway, I have the second E682 with the latest firmware, setup the universes 13 - 22, and the Output type (on first page) to be 281X/1804 for all.
I am only using 2 outputs on the controller (for now) for 6 arches. 3 each output, 80 pixels each arch. I put on 240 pixels, but the end address only shows 360 channels in universe 1, not 720 (210 in universe 2)

First page

problem 2

second page

problem

Lost on what I am doing wrong.

Thanks in advance


Reply
Posts: 247
Topic starter
(@bcer960)
Reputable Member
Joined: 10 years ago

Ok, figured it out...... it was the group size. It was set to 2 on the board. Not sure what the group size is, but when I set it to 1, it worked.

Thanks for reading anyway.....


Reply
Posts: 3735
(@algerdes)
Famed Member
Joined: 15 years ago

"Group size" is when you want to have a "group" of pixels act as a single pixel. Say you want 5 pixels to all come on at the same time - all the time, you can set the "group size" to 5 and tell your sequencer that it is one. The controller will send the same data to all 5 pixels, and your sequencer is none the wiser.


Reply
Posts: 247
Topic starter
(@bcer960)
Reputable Member
Joined: 10 years ago

thank you


Reply
pmiller
Posts: 2795
(@pmiller)
Famed Member
Joined: 12 years ago

Would be a whole lot easier to setup the 682 by upgrading firmware to 5.030. With that firmware upgrade you can control each output of the 682 instead if groups of 4. Here's an example of the 682 with firmware version 5.030.

Sent from my SM-T710 using Tapatalk


Reply
Posts: 247
Topic starter
(@bcer960)
Reputable Member
Joined: 10 years ago

thanks pmiller. I did upgrade it to 5.030 before starting this.


Reply
pmiller
Posts: 2795
(@pmiller)
Famed Member
Joined: 12 years ago
algerdes wrote:"Group size" is when you want to have a "group" of pixels act as a single pixel. Say you want 5 pixels to all come on at the same time - all the time, you can set the "group size" to 5 and tell your sequencer that it is one. The controller will send the same data to all 5 pixels, and your sequencer is none the wiser.

When you set group size that also means less channels.
I have 3 arches with 54 pixels each. I have then set in groups of 6. That's 162 pixels for 486 channels. But in groups of 6 you divide the number of pixels by 6 so for me that's 27 pixels totaling 81 channels. The sequencing software and the controller should be set up to reflect 27 pixels, 81 channels.

Sent from my SM-T710 using Tapatalk


Reply
Posts: 247
Topic starter
(@bcer960)
Reputable Member
Joined: 10 years ago

Ok, Thats something i hadn't thought of. I'll keep it in mind for future elements


Reply
Page 3 / 3
Share: