pixel question(s)
 
Notifications
Clear all

pixel question(s)

8 Posts
4 Users
0 Reactions
4,970 Views
Posts: 247
Topic starter
(@bcer960)
Reputable Member
Joined: 10 years ago
[#51433]

I have a singing light bulbs element (4 bulbs in a 4X8 sheet of corplas) I made the design and there are 194 pixels in a bulb. I've named the bulbs left, left middle, right middle and right. All 5v pixels.

I am just testing them in the basement, and have a approx 5' output wire from the E682 to the pigtail for the bulbs. Now, each wire to the bulbs from the pigtail is different lengths. Right bulb being 2', left bulb being 9'. It is all 20 gauge wire. I have also injected power every 50 pixels. (and this may be part of my problem, more on this later.)

The right bulb works perfectly.

The right middle bulb, all the pixels light up, but do not follow the alternating test pattern I have in vixen.

The Left middle turns on, but the colors are wrong, and no test pattern

The left turns on, wrong colors and no test pattern.

Also, and one of the most weird things, When I stop the sequence in Vixen, the left middle and left bulbs do not turn off. In fact, I even unplugged them from the E682, and the lights still stayed on. I had to unplug the E682 to turn them off.

Power injection: I ran one wire from the E682 that supplies the pixels into the 4 bulb element. It then splits into 2 wires which each go to terminal blocks, one for the Left, left middle bulbs, one for the middle right and right bulbs. Each supply pos and neg power. It is then wired in every 50 pixels into each string.

Please tel what is going on, and what I have done wrong.

thanks
Ray


7 Replies
Posts: 247
Topic starter
(@bcer960)
Reputable Member
Joined: 10 years ago

yes, one output for each bulb. The fun part is, for testing purposes, I have only one cable from the E682. So I just plug it into each bulb one at a time, and the results are all different.


Reply
Posts: 124
(@bob-nj)
Estimable Member
Joined: 12 years ago

Are you using more than one power supply? If so, you need to keep the V+ separate.


Reply
Posts: 247
Topic starter
(@bcer960)
Reputable Member
Joined: 10 years ago

no, only one power supply, but I probably found the problem. Power supply is only putting out 4.5v, with no load. and it's only 3.1v at the furthest bulb.


Reply
Posts: 241
(@mrdudeman)
Reputable Member
Joined: 12 years ago

whats the voltage at last pixel?
20awg sounds kind of thin to me..


Reply
Posts: 247
Topic starter
(@bcer960)
Reputable Member
Joined: 10 years ago

I will check the voltage tonight. But the pigtails i bought were only 20awg. The wire i'm using is 18 awg, but i gave the 20 awg because it was the thinnest.


Reply
Posts: 1267
(@xmasinvancouver)
Noble Member
Joined: 10 years ago
MikeKrebs wrote:It sounds like a configuration problem in the controller. Make sure the universe and start channel are correct for each output. I assume you have one on each output?

His config is correct except that he wasn't using the 3-1 to 3-4 output for testing his ws2811 pixels. But I've been talking with him and saw his config. Universes, pixel type, color order etc correct no overlap. I think this is a Multiple based issue. For starters, he mentioned that there was some known backwards pixels he was going to fix. Config in vixen have yet to see it. As well, apart from power supplies dipping down to 3.1v for 5v!! (basically non functional range), my understanding is that he is running a sort of single power rail/source for injection on 20 awg wire. And that he is splitting or tapping it for injection points.


Reply
Posts: 247
Topic starter
(@bcer960)
Reputable Member
Joined: 10 years ago

Ok, after totally re-wiring it last night, I got it working. I still have a power supply not supplying 5v (4.48 max at the screws), but new meanwells on order.

Thank you all that helped make this work.

Ray


Reply
Share: