question about sett...
 
Notifications
Clear all

question about setting up a second E682

30 Posts
7 Users
0 Reactions
16.4 K Views
Posts: 247
Topic starter
(@bcer960)
Reputable Member
Joined: 10 years ago
[#51441]

I would like to setup a second E682 tonight for leaping arches. I searched the forum to find an answer, but nothing came up. I have the first as unicast, and will set up the second that way. My question is

For the second E682, do the universes start at 1 again, or carry on from the first E682 (universe 9 I think)

Thanks
Ray


29 Replies
Wildbill
Posts: 259
(@wildbill)
Reputable Member
Joined: 16 years ago

It has to have a different IP address and I think depending on what software you are using as to weather you can keep going or start at 1 again

Sent from my iPhone using Tapatalk


Reply
Posts: 247
Topic starter
(@bcer960)
Reputable Member
Joined: 10 years ago

Yes, I know to give it a second address, thank-you. I guess I'll start with 1, and see if it works.


Reply
Wildbill
Posts: 259
(@wildbill)
Reputable Member
Joined: 16 years ago

I use Xlights and just kept going up with the universe number when I got to my next E682

Sent from my iPhone using Tapatalk


Reply
Posts: 247
Topic starter
(@bcer960)
Reputable Member
Joined: 10 years ago

thank-you. I am using vixen, I was unsure that that mattered to the setup of the controller, but will continue the universe numbers


Reply
jchuchla
Posts: 8698
(@jchuchla)
Illustrious Member
Joined: 15 years ago
bcer960 wrote:I would like to setup a second E682 tonight for leaping arches. I searched the forum to find an answer, but nothing came up. I have the first as unicast, and will set up the second that way. My question is

For the second E682, do the universes start at 1 again, or carry on from the first E682 (universe 9 I think)

Thanks
Ray

You should use unique universe numbers for each unique set of channels. So you should be using unique universe numbers for each device. Except for when the same universe is being sent to more than one controller, but in that case you should be using multicast.

You can get away with reusing universe numbers with some sequencers and situations, and many people do it without seeing the problems. But it's not the right way, and best to not get in that habit. As you grow your show and experiment with different controllers of varying sophistication, some devices you run into in the future may not behave properly and you could end up with data ending up in the wrong place. Vixen enforces the spec and won't allow you to use the same universe number more than once.

You may want to give some thought to leaving some space between universe numbers on different controllers. You've got 63999 to choose from. No need to pack them tight. In the case of the 682, it supports up to 12 I think. Leave all 12 for that controller and start the next one at 13. Or skip to an even number like 21 to make your offsets easier to do in your head. That way you can adjust and expand your display over time without redoing everything.


Reply
Posts: 247
Topic starter
(@bcer960)
Reputable Member
Joined: 10 years ago

Thank-you Jon. I am looking to do this the correct way the first time.


Reply
jchuchla
Posts: 8698
(@jchuchla)
Illustrious Member
Joined: 15 years ago

I just edited my post above, you may want to read the last paragraph I just added.


Reply
Posts: 247
Topic starter
(@bcer960)
Reputable Member
Joined: 10 years ago

That is great advise, thank-you


Reply
pmiller
Posts: 2795
(@pmiller)
Famed Member
Joined: 12 years ago
jchuchla wrote:You should use unique universe numbers for each unique set of channels. So you should be using unique universe numbers for each device. Except for when the same universe is being sent to more than one controller, but in that case you should be using multicast.

You can get away with reusing universe numbers with some sequencers and situations, and many people do it without seeing the problems. But it's not the right way, and best to not get in that habit. As you grow your show and experiment with different controllers of varying sophistication, some devices you run into in the future may not behave properly and you could end up with data ending up in the wrong place. Vixen enforces the spec and won't allow you to use the same universe number more than once.

You may want to give some thought to leaving some space between universe numbers on different controllers. You've got 63999 to choose from. No need to pack them tight. In the case of the 682, it supports up to 12 I think. Leave all 12 for that controller and start the next one at 13. Or skip to an even number like 21 to make your offsets easier to do in your head. That way you can adjust and expand your display over time without redoing everything.

Yes, the 682 supports 12 universes in Unicast and 6 universes in Multicast.

Sent from my SM-T710 using Tapatalk


Reply
Page 1 / 3
Share: