problem with 682
 
Notifications
Clear all

problem with 682

24 Posts
7 Users
0 Reactions
6,970 Views
Posts: 44
(@swood)
Eminent Member
Joined: 16 years ago

I may have missed it somewhere but what type pixels are you using and make sure you have that pixel plugged into the cluster you have it programed for. When you do a test one all pixels should light up with the same color.


Reply
Posts: 2171
(@mschell)
Noble Member
Joined: 18 years ago

Richard,

If you're using the same cluster for all your strings of a given type and it's setup for the right number of strings and the right pixel type, they should all light up the same way when you use the "test" function.

If not, something isn't setup right, either electrically on the board or in your configuration.

If a given string is lighting up all white, then something may not be connected correctly. Does the same string act the same on another output of the cluster?

I would verify connections to the board. Everytime I've seen a 2801 pixel light up all white, it's either had power hooked up wrong or the data/clock signals swapped. Hooking up power wrong can damage pixels.

If the behavior follows the string, then it's a wiring or pixel issue. If the behavior follows the port, then it's a board issue or configuration mis-setup.


Reply
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago
mschell wrote:Richard,

If you're using the same cluster for all your strings of a given type and it's setup for the right number of strings and the right pixel type, they should all light up the same way when you use the "test" function.

If not, something isn't setup right, either electrically on the board or in your configuration.

If a given string is lighting up all white, then something may not be connected correctly. Does the same string act the same on another output of the cluster?

I would verify connections to the board. Everytime I've seen a 2801 pixel light up all white, it's either had power hooked up wrong or the data/clock signals swapped. Hooking up power wrong can damage pixels.

If the behavior follows the string, then it's a wiring or pixel issue. If the behavior follows the port, then it's a board issue or configuration mis-setup.

Mark

this is not my thread 🙂 this is Henri's > Barbottes post .

I just post the info from the e682 opman as an FYI .

You stated you have not assembled your e682 yet so I assumed you not aware that the 3.3 and 5v jumpers were removed on this pcb version .

I always appreciate your advice though !

Cheers
Richard


Reply
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago

White color usually signifies no data ,either wrong chip is configured or wiring is wrong ie) clock and data are reversed .


Reply
Posts: 2171
(@mschell)
Noble Member
Joined: 18 years ago

Richard,
Sorry, I did get first names mixed up between you and Henri. I should have used screen names instead....the brain seems to forget things more these days.

Thanks for the mention about 3.3 and 5v jumpers. I could have looked at the manual, but didn't take the time to check.

Henri,
Please let us know how it goes.


Reply
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago

@ Henri , as Budude suggested read page 24 it explains the jumpers and their use ,

They are for 2 wire dmx configurations of the clusters and in some instances 3 wire pxels . Imo ,you will most likely never use them though .

Richard


Reply
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago

Mark your pm box is full .


Reply
Posts: 2171
(@mschell)
Noble Member
Joined: 18 years ago

Just cleaned it out...

Thanks,


Reply
Posts: 1792
Topic starter
(@barbotte)
Noble Member
Joined: 17 years ago
angus40 wrote:@ Henri , as Budude suggested read page 24 it explains the jumpers and their use ,

They are for 2 wire dmx configurations of the clusters and in some instances 3 wire pxels . Imo ,you will most likely never use them though .

Richard

so they should be off like i did lol
as for testing .. i put the light in cluster 1 then do test patern 1 they all goes red ....then i remove from cluster 1 and put it on the other one so some are red other are white ... i guess its normal ?? as when i enter test patern 1 it is for cluster 1 right ??
cheer


Reply
Posts: 347
(@dougd)
Reputable Member
Joined: 19 years ago

you need to type in the command box chip 3,1 and chip 4,1 and that will set all 4 clusters to 2801. Then when you test in all the sockets they should be red.


Reply
Page 2 / 3
Share: