Problem mapping nod...
 
Notifications
Clear all

Problem mapping nodes to E682 / FPP / Matrix

7 Posts
2 Users
0 Reactions
2,552 Views
Posts: 33
Topic starter
(@raabaman)
Eminent Member
Joined: 11 years ago
[#41502]

1 OF 4 -- Problem mapping nodes to E682 / FPP / Matrix

Hi All,

I'm building a matrix using 12mm nodes. At this point I'm only up to 2 strings of 100 - 200 pixels, 600 channels. When I test each string individually they're fine. When I test them all at once using the E682 tests they all work. When I swap them around the controller outputs they still all work.

When I go to FPP and run the test programme there is a definite problem in the way they are now being addressed. I have tried numerous configurations and am still getting this odd display. There seems to be a problem when the second string gets to the point it goes from Universe 1 to Universe 2.

It's fine from pixel 1 - 170. When it gets to 171 it is either very dim or just off. When it gets to pixel 172 it changes colour entirely.

(It's a similar problem when I run tests in xLights)

I have gone over and over the various settings between the controller and FPP. I *think* they all look correct. I access the FPP through a wifi connection on a different subnet than the E1.31 data, which goes out through the ethernet port. Is that a problem? I think it's a bit unlikely.

Here's a detailed description of what's going on.
Sandevices E682 Main Setup Page (NEW FIRMWARE)

E682 MainPage

E682 Output Page

E682 OutputPage

Normal setting of 2 outputs spanning 2 universes - Test Green
Matrix – All Green. Ok.

File 000

(TOO MANY ATTACHMENTS - PLEASE WAIT FOR ALL 4 PARTS OF POST BEFORE REPLY!)


6 Replies
Posts: 33
Topic starter
(@raabaman)
Eminent Member
Joined: 11 years ago

2 OF 4 -- Problem mapping nodes to E682 / FPP / Matrix

Change outputs to 2 universes of 100 pixel each (no overlapping at outputs) - Test Blue

E682 OutputPage2

Matrix – All Blue. Ok.

File 001

Turn off one output (1-1) - Test Blue
(appropriate results when 1-2 is turned off instead)

E682 OutputPage3

Matrix – 1-1 OFF & 1-2 Blue. Ok.

File 002

(TOO MANY ATTACHMENTS - PLEASE WAIT FOR ALL 4 PARTS OF POST BEFORE REPLY!)


Reply
Posts: 33
Topic starter
(@raabaman)
Eminent Member
Joined: 11 years ago

3 OF 4 -- Problem mapping nodes to E682 / FPP / Matrix

TURN OFF E682 TEST PATTERN
RESET OUTPUTS TO ORIGINAL SETTINGS AS SHOWN ABOVE
REBOOT CONTROLLER

FALCON PLAYER
FPP set to 4 universes of 510 channels to run consecutively.
eg. start of universe is next available channel after previous.

Network Config:

FPP network

]

Channel Outputs:

FPP Outputs1

Channel Outputs Testing:
Only channels 1-600 (200 nodes)
All Blue

FPP Test1

Blue until node 170, then green-ish

File 003a

Zoom in on trouble spot

File 003

(TOO MANY ATTACHMENTS - PLEASE WAIT FOR ALL 4 PARTS OF POST BEFORE REPLY!)


Reply
Posts: 33
Topic starter
(@raabaman)
Eminent Member
Joined: 11 years ago

4 OF 4 -- Problem mapping nodes to E682 / FPP / Matrix

Localise the failure
Channel Outputs Testing:
Only channels 1-510
170 nodes
1 Universe

FPP Test2

Zoom in on trouble spot - annotated

File 004

Channel Outputs Testing:
Only channels 1-510
200 nodes
2 Universes (U1 + 90 channels in U2)

FPP Test3

Correct to node 170, then off (or dim)
on 171 and alternate colour on 172.

File 005

Thanks for any help!

(FINAL PART OF POSTING!)


Reply
Barnabybear
Posts: 1583
(@barnabybear)
Noble Member
Joined: 15 years ago

Hi, wow lots of info there. I think the problem you have is different sizes for a universe, 510 and 512. It looks like the E682 is set up correctly and looking for 510 pieces of data per universe, but the software your using to send test data is sending 512.
So the E682 is looking for:
Universe 1, Data 508 = Red, 509 = Green, 510 = Blue, Universe 2, Data 1 = Red, 2 = Green, 3 = Blue.

It looks like the test software is sending.
Universe 1, Data 508 = Red, 509 = Green, 510 = Blue, 511 = Red, 512 = Green, Universe 2, Data 1 = Blue, 2 = Red, 3 = Green.

The E628 is throwing 511 & 512 away as it has been told not to use them and you end up with.
Universe 1, Data 508 = Red, 509 = Green, 510 = Blue, (511 = Red, 512 = Green both get thrown away), Universe 2, Data 1 = Blue [is seen as Red], 2 = Red [is seen as Green], 3 = Green [is seen as Blue].

I think this is proberbly a querk in the way testing has been done, dating back to when a universe was the maximum you could have on an output. The only way I can see round this to check is to set the E628 to 512 channels on the configuration page whilst you are testing and set it back when you get to running sequences.


Reply
Page 1 / 2
Share: