Pixlite16 and Nutcr...
 
Notifications
Clear all

Pixlite16 and Nutcracker setup question

7 Posts
3 Users
0 Reactions
2,138 Views
Posts: 374
Topic starter
(@mberta2)
Honorable Member
Joined: 13 years ago
[#36017]

I am finally getting my pixlite16 to work with Nutcracker after a couple days of trial and error. All of my output are finally set right and working but I have 2 problems. One problem is the colors are off. I and using 2811 nodes from HolidayCoro which are RGB and I have everything else set the same. Second problem is that nothing seems to work right unless the advatek software is open, is this normal? Thanks


6 Replies
Posts: 482
(@jcmarksafb)
Honorable Member
Joined: 15 years ago

The nodes say RGB, but they may be BGR, GRB, or some other combination. The pixlite should have settings for the different configurations, keep trying different ones until you get it to output the right configuration.
John


Reply
Posts: 45
 Devo
(@devo)
Trusted Member
Joined: 13 years ago

As John said the first problem is easily fixed by changing the RGB order under the 'LEDs' tab in the advanced settings of the Assistant.
Regarding the second problem: what do you mean by "nothing seems to work right"? Do you mean the controller won't run?
The Advatek Assistant utility is only used to configure the settings on the controller. Once you have done that it is not necessary to have it open/running at all.


Reply
Posts: 374
Topic starter
(@mberta2)
Honorable Member
Joined: 13 years ago
Devo wrote:As John said the first problem is easily fixed by changing the RGB order under the 'LEDs' tab in the advanced settings of the Assistant.
Regarding the second problem: what do you mean by "nothing seems to work right"? Do you mean the controller won't run?
The Advatek Assistant utility is only used to configure the settings on the controller. Once you have done that it is not necessary to have it open/running at all.

For the rgb order should I change it in advatek assistant or change it in Nutcracker? When I tried changing it in advatek, the lights didn't work. As for the second problem I might just need to try it again. I was in a hurry today.


Reply
Posts: 45
 Devo
(@devo)
Trusted Member
Joined: 13 years ago

I don't think the RGB order can be permanently changed in Nutcracker - you are better to change it on the controller and then you won't have to worry about it anymore.

Simply changing the RGB order in Assistant utility shouldn't ever stop the lights from working. It sounds like something is awry.

Make sure you are using the latest version of Assistant utility and PixLite firmware from here http://www.advateklights.com/resources/


Reply
Posts: 374
Topic starter
(@mberta2)
Honorable Member
Joined: 13 years ago

I figured out the one problem. When I would close the advatek assistant and reopen xlights I was forgetting to click the "output to lights" box. I didn't realize you had to click it every time you open it. For the color order problem I am still a little puzzled. I tested each output on the pixlite16. Outputs 1,2,8,and 9 are working properly. The rest of the outputs are all the wrong colors. When I checked the output order in the assistant utility they are all "RGB". Is this normal? I used the same string of pixels to test each output.


Reply
Posts: 374
Topic starter
(@mberta2)
Honorable Member
Joined: 13 years ago

OK I'm not sure if this is the right way but everything is working now. Here is my pixel tree setup first. It's 12 strings of 75 nodes each and one star that is 50 nodes. So that means I'm using 13 of the outputs on my pixlite16. I went into advatek assistant and set each output as its own universe (12 universes starting at 1 and ending at 225 and the 13th universe starting at 1 and ending at 150). I then went into xlights and setup 13 universes. I tried it out and it seems to be working fine. All of the outputs are the right colors and seem to be working right. I have the star built already so I can really tell that it's working right. Looks amazing. Did I set this up right?


Reply
Share: