I built custom pixel icicles 2 years ago and have always had what appeared to be "data" issues with them. This will flicker at weird times, work normally at others. The prop is 804 WS2811 pixels, broken up into 134 icicles that are 6 pixels in length. I built this prop in a modular manner in "bars" that can be taken down and easily stored. Each bar can be tested solo, which I am doing now, and I am finding some VERY strange things in some of the bars, not all.. I am running these on an e6804 sandevices board. there are test patterns that you can run when you plug pixels into it. 1 is all red, 2 is all green, 3 is all blue. When I wire up a bar to the board, I am running 1, which is all red. and find that the first pixel is blue, and all others are magenta. Now, if I touch the data connection on the pixels, suddenly, all pixels turn red, as they should be. if I take my finger away, they go back to 1 blue, and all magenta. I've built ALOT of pixel elements, but most are between 20 - 150 pixels. Not sure if this a symptom of a "big" build, or what. Has anyone ever experienced this??? I have no idea what is going on, or what I did wrong. Please help.
I thought it was a first bad pixel initially as well, however, I pulled it, tested it and found it to be okay. Changed it out anyway. Problem still persists. I am touching the bare data line right at the first pixel.
Are you using earth ground on you power supply? I.e the green wire on a 3 prong plug.
have you followed the "where data goes so goes v-" rule? v-from the controller must run with the data line.
MartinMueller2003 wrote:have you followed the "wher data goes so goes v-" rule? v-from the controller must run with the data line.
I am not. Data is the only wire coming from the controller, but I am powering with the same power supply. I will give this a shot later today and see if it fixes my issue. Thanks!
MartinMueller2003 wrote:have you followed the "where data goes so goes v-" rule? v-from the controller must run with the data line.
A bit of progress here, but also the realization that I probably built this thing entirely wrong. I'll attempt to explain a little better here.
The prop is Pixel Icicles. It consists of 134 icicles that are 6 pixels each, 804 total pixels. I built in a modular way so that each icicle could be replaced without any intervention, rewiring, soldering, etc. I cut 134 segments of 6 pixels. from the controller, I send data out into the first icicle. Data travels into the blue wire of a pigtail attached to the first segment (icicle), into pixel number 1. 12v+ and Ground are sent into the pigtail via Red and Black wires from a separate PSU. from the 6th pixel I return ONLY the data line back into the 4th remaining wire (Yellow) from the pigtail which then travels from the bar into the next segment. Yellow (or Data out), ties into segment two's Blue wire (Data In), and so on and so on, until the final 134th segment. Every segment is injected from PSU's that tie into each pigtail at the top of the bar. Martin, based on your reply earlier, I think I'm dealing with a couple of issues here.... since GND terminates at the end of every segment, I do not have GND traveling with data at all times. Also, only data is sent from the controller which is likely another issue. So then the question now is the easiest way to remedy the problem. The smart thing to do would be to do a complete rebuild and snake the pixels, minimizing the connections that need to be made. Or, is it possible to connect the GND from pixel 6 of segment 1 to pixel 1 of segment 2, pixel 6 of segment 2 to pixel 1 of segment 3, and so on....
Thoughts?
One of the basics that you probably already know, but should be said:
All electrical circuits have one thing in common. They MUST have a complete circuit. If you send power out to a device, there must be a a return line that goes back to the power source. If you send a data signal out to a group of pixels, there MUST be a return line back to the data source.
You state that you return the negative to the power source, but you do not describe how you are getting the negative data signal back to the controller.
In 3 wire pixels power and data feeds share the negative/return line.
Try tying the negative line (just the negative line) that goes back to your power supply to the negative terminal of your data controller.
By the way, I like the modular approach to the icicles. Nice. 🙂
canigian wrote: since GND terminates at the end of every segment, I do not have GND traveling with data at all times.
This is one of the issues that is likely causing (or at least contributing your problems).
canigian wrote: Also, only data is sent from the controller which is likely another issue.
A lot of people that have tried this have had reliability issues.
canigian wrote:So then the question now is the easiest way to remedy the problem. The smart thing to do would be to do a complete rebuild and snake the pixels, minimizing the connections that need to be made. Or, is it possible to connect the GND from pixel 6 of segment 1 to pixel 1 of segment 2, pixel 6 of segment 2 to pixel 1 of segment 3, and so on....
Thoughts?
replace the single data wire coming from the last pixel in the icicle with a pair of wires (24AWG is enough here). One for data and one for v-. Connect both of these to the tee going to the next icicle. Data and V- both go through the tee where they are joined by V+ and V- from the PSU. Rinse and repeat for each icicle. Using this method you can also connect multiple PSUs without issue.
