DMX on ESPixelStick
 
Notifications
Clear all

DMX on ESPixelStick

17 Posts
6 Users
0 Reactions
4,934 Views
Posts: 401
Topic starter
(@kensington)
Reputable Member
Joined: 11 years ago
[#52499]

I have a bunch of the ESPixelsticks laying around and I’m looking for things to do with them. I read in the build manual that they’ll output serial DMX if the RS-485 interface is bypassed or an RS-232 to RS-485 converter is used. Has anyone done either, and if using a converter, which one?


16 Replies
Posts: 119
(@packetbob)
Estimable Member
Joined: 17 years ago

I have made a few using the cheap MAX485 modules....
I have made up build guides for the regular and DMX versions:
http://zappedmyself.com/projects/espixelpops/


Reply
Posts: 401
Topic starter
(@kensington)
Reputable Member
Joined: 11 years ago

Exactly what I needed, thanks!


Reply
ukewarrior
Posts: 4674
(@ukewarrior)
Illustrious Member
Joined: 18 years ago

I am planning to design a board that brings this DMX capability to the pixel pops family.

I am thinking it will be a pixel pops board that can take these DMX modules as a daughter board.
What do you all think?


Reply
Posts: 119
(@packetbob)
Estimable Member
Joined: 17 years ago

That would be nice.. There is no cheaper way to get a E1.31 to DMX bridge...


Reply
Posts: 401
Topic starter
(@kensington)
Reputable Member
Joined: 11 years ago
ukewarrior wrote:What do you all think?

I’m thinking shut up and take my money. 🙂

Would be nice to have compatibility with the ESPixelStick, although I’m guessing the pinout on both are pretty similar on the output side.


Reply
MartinMueller2003
Posts: 7614
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago
ukewarrior wrote:I am planning to design a board that brings this DMX capability to the pixel pops family.

I am thinking it will be a pixel pops board that can take these DMX modules as a daughter board.
What do you all think?

DaughterBoard == more connections and physical space. Unless you mean an inline daughterboard. PixelPop and PixelStick are just a baseboard and an ESP-01. Make a DMX Baseboard or make a board that takes the Serial output on the existing board and turns it into RS485 (aka RS485 Transmitter) then the other end can be any DMX device OR if in pixel mode you have a long distance pixel signal using the RS485 levels that the other pixel extenders use.


Reply
Posts: 119
(@packetbob)
Estimable Member
Joined: 17 years ago

The PCB would be larger to accommodate the RS-485 module but you can remove the +5 regulator, 2N7000 and their associated resistors...

You could make the PCB smaller by using a discrete RS-485 driver (8 pin DIP) but the cost of the RS-485 driver (and associated resistors) may be more than the cost of the additional PCB required for the module.. The modules are really cheap (think I pay about $0.60 Canadian each).

You may want to add an extra GND terminal so you can connect a ground for the DMX connector as the module only has Data + and Data - (AB)


Reply
Posts: 1420
(@1pet2-9)
Noble Member
Joined: 6 years ago

Necroing the thread, since I just bought a forkineye ESPixelStick and flashed in 3.2 firmware. I see in the config utility that you can set it to Serial (DMX/Renard). So I can't just connect 3 of those 4 output pins (I assume D+, D- and V-) and go directly to a DMX 3-pin XLR?


Reply
MartinMueller2003
Posts: 7614
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago
1pet2_9 wrote:Necroing the thread, since I just bought a forkineye ESPixelStick and flashed in 3.2 firmware. I see in the config utility that you can set it to Serial (DMX/Renard). So I can't just connect 3 of those 4 output pins (I assume D+, D- and V-) and go directly to a DMX 3-pin XLR?

Is there a reson you went with 3.2 insted of V4?


Reply
Page 1 / 2
Share: