Pixels and Wattage
 
Notifications
Clear all

Pixels and Wattage

16 Posts
5 Users
0 Reactions
3,779 Views
Posts: 29
Topic starter
(@sroberts1519)
Trusted Member
Joined: 10 years ago
[#55817]

Been looking at some threads on this site, and am confused with peoples calculation.

It sounds like that both 5V and 12V pixels use around 0.3 Watts per pixel (at full brightness).

YUet people use 50 milliamps per pixel regardless of 5V or 12V.

Ohm's law doesnt compute. At 0.3 Watts, 5V would be 60 milliamps and 12V would be 25 milliamps.

Which is it? or is wattage use different between 5V and 12V?

Also, how much less watts are used when the led's are ran at say 30% (I have home grown controllers, and I reduce brightness by multiplying the LED value by the factor, say 0.3). I know that reducing LED brightness is not linear, but is it safe to assume if I run at 25% brightness, I can reduce the 0.30 watts by half down to 0.15 watts per led?

Thanks in advance,
Shawn


15 Replies
Posts: 226
(@thomasled)
Estimable Member
Joined: 5 years ago
people use 50 milliamps per pixel regardless of 5V or 12V.
Ohm's law doesnt compute. At 0.3 Watts, 5V would be 60 milliamps and 12V would be 25 milliamps.

5V strings are one LED per pixel. The typical 12V string has groups of three LEDs in series. So your math needs to accommodate that.
For example: (0.3W x 3) / 12 = 75mA.
BTW, 0.3W per pixel is a generalized estimate. Don't expect the 5V vs. 12V string values to be exact matches.

I know that reducing LED brightness is not linear, but is it safe to assume if I run at 25% brightness, I can reduce the 0.30 watts by half down to 0.15 watts per led?

Visually (what your eyes see) is not a linear affect as non-mapped brightness levels are changed. But at the electrical level, changing the PWM signal percentage should have a linear effect on power consumption.

- Thomas


Reply
Posts: 29
Topic starter
(@sroberts1519)
Trusted Member
Joined: 10 years ago
ThomasLED wrote:5V strings are one LED per pixel. The typical 12V string has groups of three LEDs in series. So your math needs to accommodate that.
For example: (0.3W x 3) / 12 = 75mA.
BTW, 0.3W per pixel is a generalized estimate. Don't expect the 5V vs. 12V string values to be exact matches.

Visually (what your eyes see) is not a linear affect as non-mapped brightness levels are changed. But at the electrical level, changing the PWM signal percentage should have a linear effect on power consumption.

- Thomas

5V 2811 strings have 3 LEDs also - how else does it provide you with 255, 255, 255 color control?

the 2811 LEDs get a digital signal at (I think) 800 kbps - my controllers have no PWM - they are dimmed by reducing the RGB values.

Shawn


Reply
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago

5V 2811 strings have 3 LEDs also - how else does it provide you with 255, 255, 255 color control?

Rgb leds of course .

Each pixel has an RGB led unless otherwise states rgbw rgbww etc . I cant say I have ever seen a pixel string that has 3 leds in series .

I am lost to what either of you are referring .


Reply
Posts: 226
(@thomasled)
Estimable Member
Joined: 5 years ago
5V 2811 strings have 3 LEDs also - how else does it provide you with 255, 255, 255 color control?

The standard 12V strings have three LED components in series, 3xRed, 3xGrn, 3xBlu. Each series group gets 12V.


Reply
Page 1 / 4
Share: