Pixels Acting Errat...
 
Notifications
Clear all

Pixels Acting Erratically

25 Posts
8 Users
0 Reactions
21.1 K Views
Posts: 11
 Guy
Topic starter
(@guy)
Active Member
Joined: 7 years ago
[#52451]

Hello everyone, thanks for accepting me into the community!

My WS2815 pixel string behaves erratically after power on.
Video of power on, behavior starts at about 30 seconds in: https://photos.app.goo.gl/6tbdcm94SqBwtyi97 (they are getting no additional data other than to turn on to the soft orange color, so the rainbow color is not something I am asking them to do)

I've been getting into Year Round Christmas Lights thanks to Home Assistant and Dr. Zzs, and I got 1/2 of my project working. I've been working on this particular project for months now, and it is slowly coming together. I got one strand of LEDs working fine, but my second strand is responding as in the above video. Using the working LED setup as my "known good" I've swapped out various bits and pieces and I think the error is in my wiring. I've increased the wire gauge to 18 (from my original 22) and that is not doing any better. It is a 25' run of 18/4 solid core wire.

I started thinking it might be voltage drop, but the lights should dim vs. flash random colors, right?

Has anyone seen anything like this before? Any suggestions as to what to try next? I was thinking about trying to solder a single pixel in the middle of the 25' run to act as a data repeater, but thought I'd ask a community before trying anything random.

Thanks for the help!

Items in the Project:
1x 12v 400w PSU
2x D1 Minis running WLED firmware, powered via buck converter from the PSU.
2x WS2815 12v LED Pixel strings, one is about 450 LEDs, the other around 400.


24 Replies
wilmar
Posts: 2115
(@wilmar)
Noble Member
Joined: 8 years ago

I had some 2811 bullets freaking out one time ... ended up being a ground issue . Not saying that’s what it is jus something I delt with

Sent from my iPhone using Tapatalk


Reply
Posts: 11
 Guy
Topic starter
(@guy)
Active Member
Joined: 7 years ago

Yeah, I've had my share of ground issues. But everything is grounded to the same PSU. I know very little about electrical engineering though.


Reply
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago

Your data line is direct from the D1 to the pixel strip ?
Have you tried a level shift to convert the 3.3v data to 5v ?


Reply
Posts: 11
 Guy
Topic starter
(@guy)
Active Member
Joined: 7 years ago

My mistake, I forgot to include that in my list of items. Yes, I have logic level shifter taking the 3.3 to 5v data.

Since this is a WS2815, I have two data lines running to the LED strips.


Reply
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago

Have you tried with just 1 data line ?


Reply
Posts: 11
 Guy
Topic starter
(@guy)
Active Member
Joined: 7 years ago

Yes, same error.


Reply
Posts: 119
(@packetbob)
Estimable Member
Joined: 17 years ago

I has a similar issue with some WS2811 bullets on long cables... Every once and a while I was getting random color flashes.. I added buffered between each fixture and this seemed to help but not a huge amount... Was planning to shorten the cable runs but didn't want to due to the design of the display. For some reason I ended up testing with a different power supply (same make and model) and the problem went away....

Moved it back to old power supply and the problem re-appeared....

So try using a different power supply......


Reply
Posts: 11
 Guy
Topic starter
(@guy)
Active Member
Joined: 7 years ago
packetbob wrote:I has a similar issue with some WS2811 bullets on long cables... Every once and a while I was getting random color flashes.. I added buffered between each fixture and this seemed to help but not a huge amount... Was planning to shorten the cable runs but didn't want to due to the design of the display. For some reason I ended up testing with a different power supply (same make and model) and the problem went away....

Moved it back to old power supply and the problem re-appeared....

So try using a different power supply......

Worth a shot! Here is the PSU I'm using. I'll order a new one tonight and see if I get any change! https://smile.amazon.com/gp/product/B06VWV5YCH/ref=ppx_yo_dt_b_asin_title_o08_s00?ie=UTF8&psc=1


Reply
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago

Have you tried reducing the length/# of pixels to see what you can control stable /successfully ?
How about measuring the output DC voltage from the power supply ?


Reply
Page 1 / 3
Share: