I'm refining my layout and trying to find the simplest solution for powering my pixels. While going over my layouts I realized that if I power a few of my pixel strings from the end of the string only, I could eliminate 30'+ power runs to the first pixel. I know I will need to fuse each line from the power supply to the pixel strings, only have the data line connected to the controller and will run null pixels as appropriate. My question is are there any issues that may arise with powering a pixel string from the end of the line only or something else that I may be overlooking? I have noticed doing a few tests that I sometimes get a random pixel that remains red when no signal is being sent from the controller, but otherwise no other problems.
You do need to have a ground line between the controller and the first pixel.
What controllers? You can flip the string with the Sandevices.
I am using SanDevices with a E682. However I don't think flipping the string on the controller helps in my situation as I'm not wanting the last pixel in the string to be the beginning. My problem is that my layout is very spread out since I'm outlining my entire roof profile with pixels on all sides of my house. To accomplish this I have two E682's that will be on opposite ends of my house and are centrally located to the beginning of most pixel strings within 10'. However I have 4 pixel strings (2 for each controller) that are 30-35' from the E682. After doing some homework, I don't really want to run 35' of heavy gauge wire just to get to the beginning of these strings. At first I thought of adding a small IP68 power supply for each of these 4 strings and power each individually , but I keep adding more elements near these strings and I also have Pixabulbs that wrap around my entire house that I need to inject power on.
That's when I got the idea of having 2 locations where I will use one of my larger power supplies in an enclosure near where these pixels, elements and Pixabulbs are. All my power runs from the power supply would be about 5' and I would follow all the guidelines regarding use of multiple power supplies. I would probably power my null pixel off the E682 and then break the V+ line there and have all the power for the string coming from the end of the pixel string. Hopefully that makes what I'm trying to accomplish a little more clear.
reelpilot wrote:I am using SanDevices with a E682. However I don't think flipping the string on the controller helps in my situation as I'm not wanting the last pixel in the string to be the beginning. My problem is that my layout is very spread out since I'm outlining my entire roof profile with pixels on all sides of my house. To accomplish this I have two E682's that will be on opposite ends of my house and are centrally located to the beginning of most pixel strings within 10'. However I have 4 pixel strings (2 for each controller) that are 30-35' from the E682. After doing some homework, I don't really want to run 35' of heavy gauge wire just to get to the beginning of these strings. At first I thought of adding a small IP68 power supply for each of these 4 strings and power each individually , but I keep adding more elements near these strings and I also have Pixabulbs that wrap around my entire house that I need to inject power on.That's when I got the idea of having 2 locations where I will use one of my larger power supplies in an enclosure near where these pixels, elements and Pixabulbs are. All my power runs from the power supply would be about 5' and I would follow all the guidelines regarding use of multiple power supplies. I would probably power my null pixel off the E682 and then break the V+ line there and have all the power for the string coming from the end of the pixel string. Hopefully that makes what I'm trying to accomplish a little more clear.
The flipping was brought up because you could flip the string on the house and then tell the controller it's flipped and still have the order of the pixels as if it's not.
For example say you want left to right so you put your pixels on your roof line that way but to get to the left that's the far left corner of your house so a long run from the controller/power to the start. What you say your doing is still running the data to the far left but powering from the right. So far left is pixel 1.
If you flip the entire string so pixel 1 physically is right then you can power and push data from the right but tell the controller that the string is reversed so that your first pixel is still left.
Keep in mind if you have long runs you may need power injection so you will still need longer power runs for that.
