Pixel Power Injecti...
 
Notifications
Clear all

Pixel Power Injection

96 Posts
23 Users
0 Reactions
30.5 K Views
Electrified3
Posts: 716
Topic starter
(@electrified3)
Prominent Member
Joined: 13 years ago
[#30083]

Seems there is a lot of confusion when it comes to pixel power injection. I took a few pixels, 200-2811 5VDC 50/50 pixels bullet style from Diy Led Express in my case and built a quick controller using an E6804 controller, a 300W 5VDC power supply in a CG-1500 case to try to show what we are talking about. What it is, and try to show you how easy this is to over come.

The first few shots are just how easy to build a controller using the E6804 with a power supply in an E6804 enclosure. Very simple, nothing too crazy, no adaptor plates or anything. I did add in terminal blocks, I do like a clean install easy to work with, easy to troubleshoot and add on as time goes on. Don't panic about that part, just connect the wires together with marrettes or whatever you like, connect them right to the board, whatever works for you.

I added in 1 quick connector to tie into my light string then. I like female out, male as secondary, like your plugs in your house, female receptacle on the wall, male for whatever you plug in. I attached it to output 1 from the controller.

Next I added 50 pixels using a 20' of #16AWG as an extension, just twisting the wires together to the connector and crimp ons where it will connect to the pixels.

I set my E6804 to output a test colour and set it to 50 pixels.

Then I added another 50 to the end of that string and set controller to 100 pixels.

Then I added another 50 pixels and updated my controller to 150 pixels.

Then I really pushed it and added another string so now 200 pixels all in series off of the same output, 5VDC off of a single output pushing through alot of wire and 200 pixels. Turned out the lights to help see it, the pixels to the right(start) are much brighter than the left(End). THIS IS COLOUR WASH!!! It is really voltage drop, probably like 5.2VDC going in and if I measured the end probably down to 4VDC or so. Should have dug out my multi-meter while I was doing the test.

Now the image will show the start of the string very bright and fading out as it moves towards the end. This is colour wash, what we are talking about. This is just off of a base colour of the pixel, if you had a colour that was a combination of the 3 colours (RGB) it would be even more amplified.

End of part 1, won't let me add any more images......

100 4606
100 4609
100 4612
100 4613
100 4623

95 Replies
Electrified3
Posts: 716
Topic starter
(@electrified3)
Prominent Member
Joined: 13 years ago

So how do we fix this. Well it is very easy. We need to get the voltage back up to get them even.

In my case, since I like injections to be done in an enclosure, again, easier to troubleshoot later, I add another connector to my controller. This time I am only going to connect my 5VDC and Common, no need to connect the data line. I just connect them with my 5VDC and common going out to my string, it already has a fuse on the board and in my case I have them going to my terminals so very easy to add in. You should see now another quick connector and connections made to the same terminals, pick your poison, double them up on the output from the controller, marrette them together, tape them together, whatever works for you. Again, I like mine clean, so I use terminals.

Now with this new quick connector I attach it to the end of my string of pixels, just power and common. Again I add 20' of #16Awg Extension, twist my wires together and use crimps to connect to my pixels. This is one cable now going to the end of my string of pixels using just power and common.

Now here is a picture before injection with Red.

Now after with Red.

Now here is a picture before injection with Green.

Now after with Green.

I should have done Blue as well, but oops.

Hope this helps you guys understand power injection, what it is and how easy it is to overcome.

It gets a bit more complicated when using more power supplies and so forth, but not that much.

There is no secret VooDoo here, just some basic electrical principles and they are very easy to over come.

This is all with 5VDC pixels, after running this test I would think you may get 12VDC pixels 200 long no problem without injection unless you are very picky.

Another note, this was all done with low gauge wire, no soldering just twisting and crimps, soldering will help as well!!!

Hope this helps a few of you wondering about the pixel power injection VooDoo.

100 4625
100 4631
100 4630
100 4633
100 4632

Reply
navyav8tr
Posts: 229
(@navyav8tr)
Reputable Member
Joined: 13 years ago

Thanks! Great post, very informative.


Reply
dsmjuggalo
Posts: 663
(@dsmjuggalo)
Prominent Member
Joined: 15 years ago

Excellent post. How about some pictures using a tee. I've done power injection but just at the end of a run. Curious to see some pictures of people using tees to continue the run.


Reply
Posts: 30
(@randyjb77)
Eminent Member
Joined: 13 years ago

Was just wondering what the grey block next to the power supply was. It looked like some kind of distribution block


Reply
Electrified3
Posts: 716
Topic starter
(@electrified3)
Prominent Member
Joined: 13 years ago
dsmjuggalo wrote:Excellent post. How about some pictures using a tee. I've done power injection but just at the end of a run. Curious to see some pictures of people using tees to continue the run.

I have never used "T"s before, like I said I keep all of mine in an enclosure to keep a clean and easy to trouble shoot system. After years of being an industrial electrician guess I have my ways and my experiences. Very difficult to trouble shoot a "T" when it is freezing outside rather than just pop the main controller open and hit it with a multi-meter.

Maybe if that is your method generate a post, would be good for everyone to understand their options. Not something I do myself so I wouldn't be the person to post that, just not my bag.


Reply
Electrified3
Posts: 716
Topic starter
(@electrified3)
Prominent Member
Joined: 13 years ago
randyjb77 wrote:Was just wondering what the grey block next to the power supply was. It looked like some kind of distribution block

The Grey block is just a strip of terminal blocks. That is why I showed the DIN rail in the first shot, then added in the terminal blocks after. The terminals just snap right onto the rail. Terminal blocks are a basic staple of a control system in an industrial environment, gives you a place to connect wires easily in order and use your multi-meter to test from. Saves also having a pile of wire in random order just twisted and connected together, There are all sorts of suppliers, all kinds of types and styles, but is a very handy thing to use.


Reply
Posts: 2229
(@plasmadrive)
Famed Member
Joined: 15 years ago

The real test is when you run full on white. You will find the red is more efficient then the blue and when the voltage starts to drop your color temperature will start to shift. If you are using flex strips, you will find that they start to shift color temp about 1.5-2 meters from the power feed point.

I am not sure what you mean by "color wash" as a technical term relating to color brightness


Reply
Posts: 654
(@szaske)
Noble Member
Joined: 14 years ago

I appreciate you trying to to be helpful, but you seemed to skip over the stuff that always has me wondering. And that is how to elegantly splice power back into the cable. I would like to see a diagram of how that second connector connects to your pixels.

The way I've done it in the past (and it seems to work) is something like this:

Power supply --(wire pair #1)--> 5v hot and neutral to pixels 1, 2, 3...100 (power lines end, data line continues)
Power supply --(wire pair #2)--> 5v hot and neutral to pixels 101, 102, 103...200 (power lines end)

In my solution, I've essentially split the 1 line into 2 parts. Are you saying that you can supply power to both ends of one string or strip both hot and neutral without causing some sort of problem? This is where my knowledge of power fails me. I would think having power coming from both ends of a wire would cause problems.

-=Steve


Reply
Electrified3
Posts: 716
Topic starter
(@electrified3)
Prominent Member
Joined: 13 years ago
pythan wrote:The real test is when you run full on white. You will find the red is more efficient then the blue and when the voltage starts to drop your color temperature will start to shift. If you are using flex strips, you will find that they start to shift color temp about 1.5-2 meters from the power feed point.

I am not sure what you mean by "color wash" as a technical term relating to color brightness

Thanks for your comments and superior intelligence on the topic. Guess I am out of my mind to try to simplify things as much as possible so beginners would understand the entire issue and how simple the resolution is.

My sincere apologies I couldn't do it to the superior level you would.


Reply
Page 1 / 10
Share: