I’m using 2801 pixels new this year. 2 strands of 50 connected at the top of a mega tree. I’m using a E682 that has worked for the last 2 years, dual 350 watt power supplies. All of the pixels were working on the ground when tested individually. When I test them now on test pattern 1 (red) I’m getting, on output 1-1, 52 red pixels then nothing, output 1-2, 15 red pixels then random flickering colors all the way to pixel 100. Output 1-3, 75 red pixels then random colors. I stopped testing after that. I tried a brand new E682 and had the exact same outcome. I’m trying to figure out if I have a pixel or a controller problem. I’m leaning towards pixel problem but everything worked fine when each strand was individually tested. I would be very happy to hear any suggestions? This tree should be running already and my neighbors are complaining I have no lights up. Thanks.
When you say you tested on the ground - does that mean the exact same cabling as you have now? Have you added extensions, etc in between? Are these 5v?
Some WS 2801 are flaky to say the least , I have 500 of the bullet style and they fail randomly.
I am not certain if it is a design flaw or poor soldering but I have chalked them up with the LPD 6803 as just another cheap and disposable pixel type .
budude wrote:When you say you tested on the ground - does that mean the exact same cabling as you have now? Have you added extensions, etc in between? Are these 5v?
Cabling is the same, but I only tested one strand at a time. They are 12 volt and the pig tails came already soldered on. I suck at soldering.
angus40 wrote:Some WS 2801 are flaky to say the least , I have 500 of the bullet style and they fail randomly.I am not certain if it is a design flaw or poor soldering but I have chalked them up with the LPD 6803 as just another cheap and disposable pixel type .
I switched over from Ray's Tm 1804 because they failed when it got moist outside. I had the 2801 on my roof last year with no issues, this year a lot of issues.
Chris A wrote:Cabling is the same, but I only tested one strand at a time. They are 12 volt and the pig tails came already soldered on. I suck at soldering.
one string tested each time on same cluster of E682? There may be a settings issue on the setup page then
Chris A wrote:I switched over from Ray's Tm 1804 because they failed when it got moist outside. I had the 2801 on my roof last year with no issues, this year a lot of issues.
I had 1 issue first year with them . 4 issues last year and to many this year to be bothered with them .
I am ordering more tls 3001's to replace them for my text matrix .
I hope for you it is a simple solve this late in the season .
Also , these are the 12v from Ray a came as 85 per string .
Cheers
I just bought an e682 kit I built it and tested it with my pixels.
Then i set up vixen and started to programme the universes and outputs of the e682 all working great. As I tinkered a little more doing vixen and poutpiut changes, I thought I had a problem. So I went to the controller web-page and set it to a test pattern.
I thought all the outputs worked before on test 14 so all should work now. I had all sorts or odd things.
I sent Jim at sandevises the list below with a screen shot thinking something on a chip must have broken. All I needed to do was set 4 as number of outputs used on each channel.
I assumed that the test sequence would override all my setting, But the e682 only shows the test pattern on the currently selected outputs.
Finding this out really sorted my issues hopefully yours will be quickly dealt with good luck
I have linked to my controller without any problems and can see Vixen sending data packets.
Set to test sequence 14
channel 1 = 1-1* nothing 1-2 nothing 1-3 all lit green redish1-4 all lit green red ish
channel 2 = 2-1 Shows correctly* 2-2 greenish 2-3 greenish 2-4 green ish
channel 3 = 1-3 test 2-3 Shows correctly 3-3 greenish 3-4 greenish
After more testing I'm really leaning towards pixel failure. I ran test 4 and many pixels were skipped or lit up as odd colors. I'm assuming the data wires have been compromised and some pixels have failed. I may switch over to 2811 pixels next year. Hopefully there will be fewer issues.
Hi, you state at the top of a mega tree. As the E682 tests as far as I know run the pixels at 100% brightness, it might be worth trying a single colour from your sequencer at only 10%. If this is a volt drop issue, running at 10% will draw a 1/10 of the current and you will only get 1/10 of the volt drop, so in theory you should be able to run 10 times more pixels before the problem occurs.
Any way it’s a quick test to eliminate volt drop as a problem.
