J-Channeling became my friend a few years back as well. I'm using strips instead of nodes on my house, but here's a link to how I did mine. In the video I was using Dumb RGB strips, but have since replaced them with Pixel Strips. I leave mine up all year and use them for the different holidays.
Starts around the 7:08 mark
Little_b wrote:J-Channeling became my friend a few years back as well. I'm using strips instead of nodes on my house, but here's a link to how I did mine. In the video I was using Dumb RGB strips, but have since replaced them with Pixel Strips. I leave mine up all year and use them for the different holidays.Starts around the 7:08 mark
Wow, some serious LOR boxes you've purchased over the years! Love the display... I'm stealing your fountain arches! 😀 Looks like you used F channel, not J channel. Did you use Vinyl or Aluminum? Vinyl seemed so flimsy to work with, although I know it's strong enough against many elements except scissors, and probably lighter than aluminum. Being in Florida and I want to have the trim year round, I had to think of the elements and possible hurricanes, so while F channel would be easier to "slip in" the fascia, J channel worked better for me with the bullet pixels and to screw in to the fascia/soffit. Either way (J or F channel), it's another interesting use of something not made for it's intended purpose.
BTW, how much power do you draw with what I would hope and presume are all mini-led strings and not incans? I assume you have several dedicated 20A circuits in your main panel for Christmas? Is discussing power bill increases around here like asking a woman her age... you just don't ask?
AJR214 wrote:Bigred... I'm new to the pixels this year. Thanks to information I've found around here and youtube, I found out about J channel and decided to go that route for the house trim. I went with pixels facing out for full exposure. I used aluminum J channel instead of vinyl as I have brown aluminum fascia and soffits. I also went with 2" spacing so I had close to 500 holes to drill for the front trim. Here are some pictures...Front of House
Adding Pixels
Undershot of mounting at 90°, pixels, and wire tucked away
What it looks like at a 45° Angle
Test of clipping on a second piece to make it look solid
I'm trying to get a video together, but if you have questions, ask and I'll do my best.
Love the look. Planning on doing mine soon with J-channel too!
Was the aluminum J-channel something you had to order? I looked at both Lowes and HD but all they stock is the vinyl. Also, what size hole did you drill for the nodes?
So I used Vinyl F and J channel. I think the J is what I use on the roof outline (This part comes down do to heat precautions). The strips are attached the same way, but I just layed them on top and used a shingle clip on both sides with a twist tie to hold them down. It took a couple wind storms to figure out that I needed to attach at least every 3' to keep it in place.
As far as attaching the Channeling to the fascia, if you look at my video I cut out the section that goes around the screws. (At first I thought I'd be taking them down and wanted to eliminate a step) If you're worried about them coming loose, you could always remove the screw, not cut out the section, and slide the channeling in and put the screw back which would more permanently attach them. Mine have never fallen out, even with the Icicle lights hanging off the back.
I still have about 1/3 to 1/2 my display in incandescent lights. (Trees, House wrap, Mega Tree, Icicles, Wreaths) I like them better, plus I got such a killer deal on them that I bought so many that I still have a couple hundred new strands to replace faulty ones with. In my newer videos you can see where I've started replacing with Pixel Nodes in several props. A few years back I had to add a breaker panel in the garage and ran several 20A lines to the eaves for power.
cjrobin27 wrote:Love the look. Planning on doing mine soon with J-channel too!Was the aluminum J-channel something you had to order? I looked at both Lowes and HD but all they stock is the vinyl. Also, what size hole did you drill for the nodes?
In Home Depot or Lowes, you can find the Aluminum J-Channel back with the downspouts and other aluminum materials. At Home Depot, I know it's $5.80 for a 12' piece. Find a local aluminum company, probably one that does screen enclosures. They will have the J and F channel (F is more expensive). My local shop had 12' J channel for $4.20 a piece. I bought 17 in chocolate brown for the front of the house. I used 7 on the trim, and will use the rest around the trim of the garage, 2 windows, doorway, and sides of the rock to make pixel poles. I also bought 10 pieces in bronze to match my pool enclosure as I'm putting pixels out there as well.
I used an 11.5mm drill bit at first, but then went to 15/32 or 29/64 I think (I will check when I get home but it was 1 or 2 fractional sizes below 1/2") because I use a deburring bit to widen the hole a smidge while cleaning any rough edges. When using the drill press to make the holes, be sure to take your time. Literally count to 6 or 8 while pulling down slowly to make the hole. If you try to go quick, it mangles the aluminum. Let the bit bore out the hole like butter rather than beating it up.
