Permanent Pixels Un...
 
Notifications
Clear all

Permanent Pixels Under Eaves

25 Posts
11 Users
0 Reactions
20.6 K Views
Posts: 12
Topic starter
(@argento)
Active Member
Joined: 10 years ago
[#44681]

Hey gang, I am brand spanking new to the forum and large pixel arrangements. The existing wikis and forum resources have been a huge help in getting my bearings on this crazy world of huge pixel counts so thanks! I am starting into this thing with baby steps and, as the title suggests, I will kick it off with a permanent under-eave project so that I can do warm white year-round and transition to holiday schemes as needed.

My first area of confusion is what type of pixel to employ. I have a 90' foot run of eave I would like to cover but it seems like even a low pixel density string (say, 20 pixels per meter) would have a huge max. amperage draw. Granted, I won't be consuming max at all times but still. Is there something I am missing? Figuring out how to get 30 - 40 amps worth of juice seems daunting.

The second question, I think, is a litte easier. Are there any specific advantages to bullet type pixels that would trump the easy installation of square pixels? It seems to me the square pixel is the obvious choice for a permanent mount but I'd rather not assume anything.

Cheers!
Argento


24 Replies
Posts: 706
(@chadowamsley)
Prominent Member
Joined: 15 years ago

http://doityourselfchristmas.com/forums/showthread.php?38747-Project-LED-house-outline&highlight=Project+house

That link is a nice step by step how Dave installed his year round pixels. In the daytime you can't see his lights unless your up close.


Reply
Posts: 192
(@rdj6107)
Estimable Member
Joined: 11 years ago

i was going to wait until tomorrow to post a reply when i had the 2nd pic, but i know how it is when you want an answer right away. i had the same issue earlier this year. prior to this year, i used cool white C9 led bulbs which i left up all year long, to replace them when i went into the pixel end of the pool, i ordered the pixabulbs that mimic the C9 look. BUT i wanted something more stealth, so i went with 12v bullet pixels. initially because of the distance i wanted to cover, 200 feet, i planned on 12" spacing but ended up settling on 6" spacing. i also shortened my total length to 150 feet. 50 feet on the 1st floor and 100 feet on the 2nd floor. for me, 6" spacing was plenty bright, and i probably would have been ok with 12" as i was wanting the house outlined traced and not brighten the entire house. with that, on my 1st floor at 50 feet at 6" spacing, it came out to 101 pixels and i didn't even need pwr injection. at your 90' with 6" spacing will yield about 180-182 pixels. you could probably inject 1/2 way and be ok. as far as what i used, this is where i owe you a pic and will get the finished install tomorrow. i used J-channel vinyl siding. fortunately for me, the beige J-channel matched my house so no need for painting. downside to J-channel was i had to drill a 1/2" hole for each node to go through and had to make a jig to fit my drill press. 315 holes total. upside to the J channel is that for 2017 i will run pwr from both sides and i can run a 14 awg wire through the J channel slot and keep it nice and tight and hidden. here is a pic of the nodes mounted inside the J channel. ill get you a pic of the installed J channel on the house tomorrow.

pixel eaves

Reply
Posts: 12
Topic starter
(@argento)
Active Member
Joined: 10 years ago

Damn, that is a super clean setup in the vinyl rail. Where did you find the pixel strings with 6" spacing?


Reply
Posts: 928
(@arw01)
Noble Member
Joined: 13 years ago

You can custom order 6" spacing from Ray Wu or Paul directly. I had a whole bunch of bullets and square done up in 6" and it's nice for coro items too.

At 12v you can go a couple hundred and feed power from both ends and normally be good, if you could punch in at 150 or so be even better.

I like the J channel idea and have considered doing something off the bottom of the facia wrap with square pixels, but I want more density.

Currenly use 30/10 strips in 3/4" pex. That can be pretty invisible too up tight to the soffits. I may look at this year in having some channel bent to a 45 and mounting Holiday Coro's aluminum with diffusion panels to it and put my strips permanently in there and perhaps go to a individual pixel strip to get more density.


Reply
Page 1 / 5
Share: