Newbie - pixel, pro...
 
Notifications
Clear all

Newbie - pixel, props, controller question

11 Posts
9 Users
0 Reactions
2,633 Views
Posts: 418
(@richienorthcott)
Reputable Member
Joined: 7 years ago

You can cut a pixel string wherever you want. Assuming you have 5V pixels make sure you have a power connection to the + and - lines every 50 pixels (or less) - this is because the pixel wires are very small gauge and suffer voltage drop. To join lengths together personally I solder the wires then slide over three lengths of adhesive-lined heatshrink which keeps things watertight. You can use a similar approach for replacing the supplied connectors with waterproof tails at the ends for outdoor use. When connecting pixel string lengths make sure you connect data in -> data out. To orientate them, the pixels sometimes have an arrow printed on, you will also see the internal IC always is on one side (I think the input side IIRC). When you buy sets of 50, the 'plug' n normally on the input end, the 'socket' on the output.


Reply
MartinMueller2003
Posts: 7613
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago
RichieNorthcott wrote:You can cut a pixel string wherever you want. Assuming you have 5V pixels make sure you have a power connection to the + and - lines every 50 pixels (or less) - this is because the pixel wires are very small gauge and suffer voltage drop. To join lengths together personally I solder the wires then slide over three lengths of adhesive-lined heatshrink which keeps things watertight. You can use a similar approach for replacing the supplied connectors with waterproof tails at the ends for outdoor use. When connecting pixel string lengths make sure you connect data in -> data out. To orientate them, the pixels sometimes have an arrow printed on, you will also see the internal IC always is on one side (I think the input side IIRC). When you buy sets of 50, the 'plug' n normally on the input end, the 'socket' on the output.

NOTE: I have seen pixel strings with socket on the 'in' side and I have seen other with the 'plug' on the 'in' side. I have seen strings with the arrows pointed up indicating that side was 'in' and other strings with the arrow pointing down indicating that side was 'out'. The point is, there are no real rules-of-thumb and you need to look at your strings to see what you have. The one constant is that if you dont inject power, you will start to have issue as your strings get longer and the distance from controller to prop increase.


Reply
Posts: 418
(@richienorthcott)
Reputable Member
Joined: 7 years ago

I'm going to correct my previous comment - from what I have seen normally the 'socket' end is start of the strip (data in) and the 'plug' is the end (data out), which is unusual for most connector best practices). But there are exceptions to this.


Reply
Posts: 10
(@kalcorn)
Active Member
Joined: 5 years ago

nitushahus- I'm new to this also. I thought I had an understanding of "plug" and "socket" but now I'm not so sure...

Anyhow, this is my thoughts to keep it easier for me and how I am setting mine up. I think of it like the wiring in your house. The receptacle in the wall is the "female" end and the cord on your lamp has the "male" end. Same way for the socket set in your tool box. The ratchet has the male square and the individual sockets have the female square.

Yes, there are exceptions for the ends but that will be how mine will be set up if they don't come that way.

Now for the data, look at the pixel closest to the end in your hand. If the arrow is pointing up that is the input side (mine will have a male pigtail/end on it); if the arrow is pointing down that is the output (mine will have a female pigtail/end on it).

At least that is how I understand it. If I am wrong, I know someone smarter than me will let me know. I am good with that.

Kevin


Reply
Posts: 418
(@richienorthcott)
Reputable Member
Joined: 7 years ago

Yes a plug has sticky-out-pins (male) socket has holes (female). It's odd that the Pixel strings normally use sockets for the input end, which means effectively your controller has exposed pins if unconnected. It is what it is.


Reply
Page 2 / 3
Share: