New pixel controlle...
 
Notifications
Clear all

New pixel controller

121 Posts
24 Users
0 Reactions
53.2 K Views
sporadic
Posts: 1199
(@sporadic)
Noble Member
Joined: 14 years ago
kingofkya wrote:what about the original ones and clones? 2811 i know had issues every time i tried. I may have had signal inegraty issues though my scope is not fast enofe for pixels.

The WS2811 datasheet I have says the same thing, 0.7Vdd. I've never tried using a 3.3V signal on them myself. My first go at pixels was with my PixelSticks which have 5V drivers and Pixabulbs.


Reply
sporadic
Posts: 1199
(@sporadic)
Noble Member
Joined: 14 years ago

Got my NodeMCU clone board in yesterday and got it up and running with the ESP8266 Arduino stuff. Pretty slick setup. Using Visual Studio 2013 Community Edition w/ the Visual Micro stuff to drive the Arduino toolkit. Can't believe these things are this easy to use. Now I need get some of the cheap ESP-01 modules and spin some boards. Question on programming headers, any pinout standards you all are sticking too, or just jumping serial adapters to flash them? Thinking I'll go with a little auto-flash circuit using the DTR and RTS lines like they do on this NodeMCU board, it has me spoiled!

NODEMCU DEVKIT SCH

Reply
Posts: 911
(@madsci1016)
Noble Member
Joined: 12 years ago
sporadic wrote: programming headers, any pinout standards you all are sticking too, or just jumping serial adapters to flash them?

Sticking to the 6 pin Arduino micro / FTDI pinout here, You can get FTDI cables and boards pretty much anywhere. https://www.sparkfun.com/search/results?term=ftdi


Reply
Posts: 29
(@ceburge)
Eminent Member
Joined: 12 years ago

I myself designed my boards to use a ftdi prop plug since I already had one. I have one of the cheap usb to ttl converters from the vendor I bought my ESP modules from. I like it cause I could use the 5V pin from it to program the device without the need of external power but it was really flakey. It would just start connecting and diconnecting for no reason. The prop plug has been flawless everytime. So thats what I am sticking with.


Reply
kingofkya
Posts: 2165
(@kingofkya)
Noble Member
Joined: 15 years ago
sporadic wrote:Got my NodeMCU clone board in yesterday and got it up and running with the ESP8266 Arduino stuff. Pretty slick setup. Using Visual Studio 2013 Community Edition w/ the Visual Micro stuff to drive the Arduino toolkit. Can't believe these things are this easy to use. Now I need get some of the cheap ESP-01 modules and spin some boards. Question on programming headers, any pinout standards you all are sticking too, or just jumping serial adapters to flash them? Thinking I'll go with a little auto-flash circuit using the DTR and RTS lines like they do on this NodeMCU board, it has me spoiled!

Regrettable "the standard" me and greg came up (well mostly me with wm2999) with with the nrf stuff.

Also fyi there is many ftdi adapters with other pinouts, and i think very few buy one via official souses.


Reply
kingofkya
Posts: 2165
(@kingofkya)
Noble Member
Joined: 15 years ago

If anyone wants it you can take my kicad drawings, you need a recent build of kicad to open it.

http://www2.futureware.at/~nickoe/
march 4th or newer.
Also you want to use opengl mode with the push and shove routing its great:)


Reply
Posts: 691
(@stormyblade)
Honorable Member
Joined: 12 years ago

I was just perusing through this forum (after responding in a thread I had started) and saw this little gem of a thread! As someone that has some GECE strings and has been looking for a good way to use them, this new controller sounds great! Last year I built up the RFColor2_4 boards and wired them into my GECE lights and replaced the GE iTwinkle boards with them as well. But, if this new controller works better...nice!!

So, please forgive me if this was mentioned, but is there a max # of pixels/nodes this new controller can run? And, because it's more "dedicated" to receiving only, it can run faster than the RFColor2_4 boards? Does someone have a way to purchase these and a BOM listed somewhere?

Thanks.


Reply
kingofkya
Posts: 2165
(@kingofkya)
Noble Member
Joined: 15 years ago

The gece bulbs are a different format of pixel were mostly talking about a ws2811 / 2812. I may be wrong but i don't think you will see much more development going on for the GECE stuff because to be brutally honesty they kinda suck.

Also gece have a hard limit on pixel chain length i think its 64 and no controller can get around that limit. Also a controllers power is somewhat irrelevant most light stuff is fairly basic almost anything can drive it.


Reply
Posts: 911
(@madsci1016)
Noble Member
Joined: 12 years ago
Stormyblade wrote:I was just perusing through this forum (after responding in a thread I had started) and saw this little gem of a thread! As someone that has some GECE strings and has been looking for a good way to use them, this new controller sounds great! Last year I built up the RFColor2_4 boards and wired them into my GECE lights and replaced the GE iTwinkle boards with them as well. But, if this new controller works better...nice!!

So, please forgive me if this was mentioned, but is there a max # of pixels/nodes this new controller can run? And, because it's more "dedicated" to receiving only, it can run faster than the RFColor2_4 boards? Does someone have a way to purchase these and a BOM listed somewhere?

Thanks.

Hi Stormy,

Yes, I will have a BOM or a group buy for my GECE via wifi design. I can't comment on the performance vs what you have used in the past but all tests so far have been good. There is the hard limit for the number of pixels at 63 because the GECE protocol uses a 4 bit address with a broadcast address at 64. There is no way around that.

Sent from my SM-T700 using Tapatalk


Reply
Posts: 691
(@stormyblade)
Honorable Member
Joined: 12 years ago

Thanks for the info guys. I would probably still be interested in buying kits for my 4 sets of GECE and GE iTwinkle lights.


Reply
Page 12 / 13
Share: