Need Help Picking P...
 
Notifications
Clear all

Need Help Picking Pixel Strips For Nutcracker Tree

29 Posts
11 Users
0 Reactions
7,011 Views
Posts: 1133
(@toozie21)
Noble Member
Joined: 19 years ago
smeighan wrote:One other comment on using flex strips. They are very waterproof being that they are in a sleeve. I had a few percent failure rate on them. The root cause was cold solder joints on the resistors. Be careful how you zip tie them. I fixed broken lights be reflowing the solder with flux. This does call for cutting the sleeve.

Sean, how did you reseal the sleeve? just put two endcaps on the cut end and rewire between them?


Reply
DrNeutron
Posts: 2018
(@drneutron)
Noble Member
Joined: 14 years ago

I ordered some 12mm end caps with my last order to test as splice points with the 10mm silicon tubing. I am hoping to be able to cut the bottom off the end cap and then slip it over the tubing and fill with silicone. I tried using plain heat shrink (with adhesive) but when it shrinks it does not make a great seal with the tubing (have to apply silicone).


Reply
smeighan
Posts: 2595
(@smeighan)
Famed Member
Joined: 15 years ago

When I ordered my flex strips they came with extra end caps and rtv adhesive. I used that


Reply
Posts: 22
(@mrbob135)
Eminent Member
Joined: 14 years ago

So what is the best way to zip tie the strips? I was assuming on the cut lines, but is there a better way to do it?


Reply
smeighan
Posts: 2595
(@smeighan)
Famed Member
Joined: 15 years ago

I tied them where the cut place is. I think I tied some too tight and they put stress in the adjacent parts. I had 4 issues out of 40 flex strips.

Sent from my iPad using Tapatalk


Reply
toy4x4
Posts: 25
Topic starter
(@toy4x4)
Eminent Member
Joined: 13 years ago

Are there any good plans out there that wraps some of these ideas up into on location?


Reply
DrNeutron
Posts: 2018
(@drneutron)
Noble Member
Joined: 14 years ago

I had the same issue with using zip ties and 2 of my strips (probably pulled too tight). This year I am using the silicon clips you can get from Ray or DIYLEDEXPRESS. I know it will be a bit more time consuming, but I plan on drilling small holes and using SS screws to attach the clips to either wood or PVC (probably PVC). Having silicon on silicon should create a nice fit and prevent anything from moving without adding any stress to the pcb.

clip

Reply
Posts: 1133
(@toozie21)
Noble Member
Joined: 19 years ago

I know I will kick myself for asking this, but "SS" screws? What are they?

I was planning on using zipties, but it looks like an ounce of prevention might be called for here....

How often do you space those out to get a good hold without overdoing it? On the ends and every meter in between?


Reply
DrNeutron
Posts: 2018
(@drneutron)
Noble Member
Joined: 14 years ago

To keep things straight, I plan on every joint (in my case it would be every 4", or every 3 LED).
SS is stainless steel (just so they do not rust).
You would be fine with zip ties, just be careful about how tight you apply them. I am going to try the silicon clips and will report back if they work better (but will be more work....but with strips at 30$ a pop it would be worth it IMO).
What can I say, I am cheap......so says the wife....:blush2:


Reply
Posts: 1133
(@toozie21)
Noble Member
Joined: 19 years ago
DrNeutron wrote:To keep things straight, I plan on every joint (in my case it would be every 4", or every 3 LED).
SS is stainless steel (just so they do not rust).
You would be fine with zip ties, just be careful about how tight you apply them. I am going to try the silicon clips and will report back if they work better (but will be more work....but with strips at 30$ a pop it would be worth it IMO).
What can I say, I am cheap......so says the wife....:blush2:

stainless steel.... what a maroon I am.

Every 4" on yours eh? I am going to do 8ft runs, that would be 25 clips per strip. I wonder if I could go with every 8" or something like that....


Reply
Page 2 / 3
Share: