My Crazy Pixel Prob...
 
Notifications
Clear all

My Crazy Pixel Problem

32 Posts
13 Users
0 Reactions
12.5 K Views
Posts: 1159
(@deonb)
Noble Member
Joined: 13 years ago

I have the exact same problem with one of my pixel strings that I replaced today. It flickers when off (or displaying black), until I touch the cable. Has been doing that since it got up. 100% repeatable. It's not weather related - it does that in hot or cold, rain or shine.

It's only one string doing this - I have 31 other strands wired the same way parallel to it that works fine. There's 6 foot of direct wire between the E682 connector and the first pixel - no solder points or pigtails in between.


Reply
jeffu231
Posts: 2457
(@jeffu231)
Famed Member
Joined: 15 years ago

You might want to experiment with some different values in the resistor packs on the e682. I had several strings flickering at times while dimming or changing colors. I changed to 100 ohm values and the problem went away.


Reply
Posts: 12
(@sandshark)
Active Member
Joined: 12 years ago

While my experience with pixels is short lived (started very basic last year), I have a lot of experience in electronics. I think it may be some kind of interference between strands and one reason it could be getting worse at cold is a bad connection that is adding resistance, making for higher susceptibility. A chip's drive could be getting weaker, but most electronics work better at cold, so that seems unlikely. Grabbing the cables is providing some capacitance between them, and possibly to local ground, depending on your footwear, and that can be a good way to reduce interference. Changing resistor values in the controller could help by increasing the signal-to-noise ratio. Putting ferrite cores over the wires (possibly also wrapping them in a wire to earth ground) may provide a similar situation to you holding them. Even just driving a metal stake in the ground and wrapping a wire from it around the bundle several times in a coil may have some impact.

I've seen voltage drop issues cause all kinds of odd issues, but I can't figure how that would be affected by you grabbing the wire bundle.


Reply
Posts: 368
(@henkvis)
Honorable Member
Joined: 18 years ago
jeffu231 wrote:You might want to experiment with some different values in the resistor packs on the e682. I had several strings flickering at times while dimming or changing colors. I changed to 100 ohm values and the problem went away.

Hi there, which resistor pack do you need to change? The ones on the ouputs (so 8 of them?) or the ones on for control (3 I believe)?


Reply
jeffu231
Posts: 2457
(@jeffu231)
Famed Member
Joined: 15 years ago

I changed just the ones on the outputs I was having trouble with.

Sent from my iPhone using Tapatalk


Reply
Barnabybear
Posts: 1583
(@barnabybear)
Noble Member
Joined: 15 years ago
szaske wrote:I'm using this standard stuff

It's not a bad solder joint. It's some sort of crosstalk on the data wire...that seems to get worse when it gets cold outside. I'm just an idiot on these sorts of things, and hoping someone more knowledgeable sees this thread and responses. I'm going to try taping all the wires together to see if that helps...or maybe I'll try using ferrites to see if that helps.

-=Steve

Hi, this is going to sound realy daft and more so if it doesn't work. But anyway, unplug the cable at one end and turn the plug to twist the cable (the more the better but don't damage the cable) then plug it back in and test. If it works I'll explain the problem and give you a better solution.


Reply
Posts: 1159
(@deonb)
Noble Member
Joined: 13 years ago
Barnabybear wrote:Hi, this is going to sound realy daft and more so if it doesn't work. But anyway, unplug the cable at one end and turn the plug to twist the cable (the more the better but don't damage the cable) then plug it back in and test. If it works I'll explain the problem and give you a better solution.

Are you going for a crude twisted pair?

So I've seen this a few times on here, and also asked this before - what's the virtue of twisted pair without a balanced signal?

I could see if the solution was "switch your E682's to balanced output and use this or that balun to ground-reference it again", but that's not what's being proposed. Mmm... Come to think of it - why isn't it? What's the cheapest inline component that can unbalance E682 balanced output? A pixel extender?


Reply
Barnabybear
Posts: 1583
(@barnabybear)
Noble Member
Joined: 15 years ago
deonb wrote:Are you going for a crude twisted pair?

So I've seen this a few times on here, and also asked this before - what's the virtue of twisted pair without a balanced signal?

Hi, With a twisted pair of cables, there is more chance they will both recieve the same level of interference and cancel each other out.
Plus it makes the data cable a worse antenna.


Reply
Posts: 1159
(@deonb)
Noble Member
Joined: 13 years ago
Barnabybear wrote:Hi, With a twisted pair of cables, there is more chance they will both recieve the same level of interference and cancel each other out.

That requires a balanced signal (and a differential receiver)?


Reply
Posts: 368
(@henkvis)
Honorable Member
Joined: 18 years ago
Barnabybear wrote:Hi, please can you post what cable you are using from you controler to you pixels (cat5, 3 core stranded or any other). If your using cat 5 or similar which colours are you using for each line. By choice I would have used one of each of a twisted pair for Ground and Data - then another pair for +ve and another pair for Ground, the last pair could be used for +ve to feed the other end of the strip.
e.g.
Green / White = Ground.
White / Green = Data. (Important this is a twisted pair with ground).
Brown / White = 5V or 12V.
White / Brown = 5V or 12V.
Blue / White = Ground.
White / Blue = Ground.
Orange / White = 5V or 12V far end injection.
White / Orange = 5V or 12V far end injection.

Thanks, this worked out for me.... don't know if twisting ground with data made THE difference, but it also couldn't hurt, so I used it....


Reply
Page 2 / 4
Share: