US Source for "gree...
 
Notifications
Clear all

US Source for "greenies"?

10 Posts
6 Users
0 Reactions
3,603 Views
Wolfie
Posts: 2225
Topic starter
(@wolfie)
Noble Member
Joined: 11 years ago
[#39339]

I would like to purchase additional connectors for the j1sys series of boards. The ausies call them "greenies". I need 4 pin and 2 pin. When I do a google on them, the only source, clap supplies, doesn't ship to US. So where do you get the connectors from here stateside?

Or does anyone have a more technical name to google other than "greenies"?


9 Replies
Posts: 66
(@mrsmith)
Estimable Member
Joined: 12 years ago
Reply
Wolfie
Posts: 2225
Topic starter
(@wolfie)
Noble Member
Joined: 11 years ago

Those don't look quite right.

This is it but this site doesn't ship to US.
http://clap-supplies.com/product/4-pin-3-5mm-greenie-connector/


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

Here you go: http://www.mouser.com/ProductDetail/Molex/39500-0004/?qs=DQ1bOpn7xPDnJJ6BeMMpqw==

These are used on the SanDevices and Falcon products as well. Be sure to get 3.5mm.


Reply
Wolfie
Posts: 2225
Topic starter
(@wolfie)
Noble Member
Joined: 11 years ago

Don't have any Falcon products, but I got a e682 still NIB I haven't even looked at it. Just arrived Wed, still in the box. Didn't know it used the same connector.

Guess I should see if the pinout is same too. Otherwise I gotta mark stuff real careful like. So I don't plug stuff in wrong controller later an pop anything. There is good and bad to having same connectors. If they match function pins, then its all good, if not, its all bad and recipe for disaster.

Thanks for the link. That looks right.

Will get some on order. Now I know the series, I can get to the 2 pin ones too. Thanks agin.


Reply
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago
Wolfie wrote:Don't have any Falcon products, but I got a e682 still NIB I haven't even looked at it. Just arrived Wed, still in the box. Didn't know it used the same connector.

Guess I should see if the pinout is same too. Otherwise I gotta mark stuff real careful like. So I don't plug stuff in wrong controller later an pop anything. There is good and bad to having same connectors. If they match function pins, then its all good, if not, its all bad and recipe for disaster.

Thanks for the link. That looks right.

Will get some on order. Now I know the series, I can get to the 2 pin ones too. Thanks agin.

The key is to maintain a color code for your wiring of rgb elements .

If black is always gnd you are not likely to become a short order chef frying things 🙂


Reply
Posts: 1159
(@deonb)
Noble Member
Joined: 13 years ago
budude wrote:Here you go: http://www.mouser.com/ProductDetail/Molex/39500-0004/?qs=DQ1bOpn7xPDnJJ6BeMMpqw==

These are used on the SanDevices and Falcon products as well. Be sure to get 3.5mm.

The Molex brand in that link from Mouser will generally ship in black - not green. And I found that these black Molex connectors are pretty tight to get out of E682 boards. They do come out with a bit of effort... but you can tell it's not quite the same thing that SanDevices uses, which has a really great fit between the terminal block and the header.

I *think* what the SanDevices use is an FCI connector, since I got these FCI headers from Mouser, and they look identical to the ones on the E682 boards:
20020107-C041A01LF

So if I were to guess at the SanDevices Eurostyle connector based on the header, it would be the FCI paired terminal block:
http://www.digikey.com/product-detail/en/20020004-D041B01LF/609-3799-ND/2261341
-or-
http://www.mouser.com/ProductDetail/FCI/20020004-D041B01LF


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago
deonb wrote:The Molex brand in that link from Mouser will generally ship in black - not green. And I found that these black Molex connectors are pretty tight to get out of E682 boards. They do come out with a bit of effort... but you can tell it's not quite the same thing that SanDevices uses, which has a really great fit between the terminal block and the header.

I *think* what the SanDevices use is an FCI connector, since I got these FCI headers from Mouser, and they look identical to the ones on the E682 boards:
20020107-C041A01LF

So if I were to guess at the SanDevices Eurostyle connector based on the header, it would be the FCI paired terminal block:
http://www.digikey.com/product-detail/en/20020004-D041B01LF/609-3799-ND/2261341
-or-
http://www.mouser.com/ProductDetail/FCI/20020004-D041B01LF

It can't be either of those as they are 3.81mm (0.15") - they must be 3.5mm to work. The link I provided was from some original SanDevices documentation as I recall and is in the Wiki. I don't really see a problem being tight - that's a good thing! I have a Falcon F16V2 with 32 connectors and I've had to pop them back in several times already because they pull out quite easily. I could see the tightness being an issue while debugging but for the final button up that would be a benefit.


Reply
Posts: 1159
(@deonb)
Noble Member
Joined: 13 years ago
budude wrote:It can't be either of those as they are 3.81mm (0.15") - they must be 3.5mm to work. The link I provided was from some original SanDevices documentation as I recall and is in the Wiki. I don't really see a problem being tight - that's a good thing! I have a Falcon F16V2 with 32 connectors and I've had to pop them back in several times already because they pull out quite easily. I could see the tightness being an issue while debugging but for the final button up that would be a benefit.

You are of course right. The -D series is a 3.81mm. The -C series is 3.5mm. E.g.
http://www.mouser.com/ProductDetail/FCI/20020004-C041B01LF

The FCI datasheet for these things are supremely awful :ohwell:

I've also gotten these ones from Phoenix Contact before from a special (Arrow Electronics I think). They work nicely but they're insanely expensive:
http://www.mouser.com/ProductDetail/Phoenix-Contact/1840382

A little tightness is fine - but the ones that ship with the E682 is good, and have never failed me in a display. You're 30% likely to pull the wires out of those before dislodging the connector. However, the Molex one is so tight that you often need to use pliers to remove it, which is not a fun way to spend a January morning disconnecting a couple of hundred outputs to take your display down.

Note however that I wire my fixtures directly to the Eurostyle connectors. If you however use pigtails in between then I can see the tighter the better.


Reply
Posts: 91
(@rednelb)
Estimable Member
Joined: 13 years ago

They are called Phoenix connectors.

If you know ANYONE in the Audio/Video installation industry, they will have tons of these. We throw them away most of the time.

Seriously go to a local commercial A/V company and ask for them.... they should let them for free or next to nothing.


Reply
Share: