Pixels flickering w...
 
Notifications
Clear all

Pixels flickering when fading out

21 Posts
5 Users
0 Reactions
5,845 Views
Posts: 37
Topic starter
(@westcoastrednecks)
Trusted Member
Joined: 16 years ago
[#39328]

I have a couple strings on my pixel tree that flicker pretty bad when fading out. They do it with all colors, not just white. Any ideas why this is happening? E6804, 5v 2811 bullet pixels run with LOR. I have attached link to the video. Thanks.

https://onedrive.live.com/redir?resid=ADB22937B6FCD3D!3143&authkey=!AN8hJbcnqjAGSyw&ithint=video%2cmp4


20 Replies
MindTrik
Posts: 1542
(@mindtrik)
Noble Member
Joined: 16 years ago

Which strings specifically. How many and what's your wiring look like...where' are your injection points, how many power supplies, how are they connected?


Reply
Posts: 37
Topic starter
(@westcoastrednecks)
Trusted Member
Joined: 16 years ago

Strings 6-7 of 12 on the tree. Power is 4' runs to the start of each string from the controller/PSU. I have 1 350 watt PSU for the tree, which should be plenty. All the strings on full white draw 180 watts.


Reply
MindTrik
Posts: 1542
(@mindtrik)
Noble Member
Joined: 16 years ago

Have you done a test using XLights on mixed colors to see if it does it?

Sent from my LG-H811 using Tapatalk


Reply
Posts: 37
Topic starter
(@westcoastrednecks)
Trusted Member
Joined: 16 years ago
MindTrik wrote:Have you done a test using XLights on mixed colors to see if it does it?

Sent from my LG-H811 using Tapatalk

I tested with the R-G-B-All and they work fine. It's only when they fade down that they flicker. I am going to check the power at the strings in the morning. I will post my findings after that.


Reply
MindTrik
Posts: 1542
(@mindtrik)
Noble Member
Joined: 16 years ago

It's got to be power

Sent from my LG-H811 using Tapatalk


Reply
Posts: 1344
(@mrsmoofy)
Noble Member
Joined: 12 years ago

Power is my guess too


Reply
Posts: 37
Topic starter
(@westcoastrednecks)
Trusted Member
Joined: 16 years ago

Here's my findings with the multi-meter. On the PSU outputs I have 4.93 volts. The controller outputs are 4.64 volts and the affected strings power input is 4.14 volts. Only the last pixel in the strings affected are pinkish. Checked all my connections and they are good. Should I turn up the PSU a little to try and get the controller output closer to 5 volts?


Reply
MindTrik
Posts: 1542
(@mindtrik)
Noble Member
Joined: 16 years ago

Disconnect everything from psu. Turn it on and attach multimeter. Use the dial to set 5v on the psu. I don't know what the percentage is here...but you can get away with something like 5.05

Sent from my LG-H811 using Tapatalk


Reply
Posts: 37
Topic starter
(@westcoastrednecks)
Trusted Member
Joined: 16 years ago
MindTrik wrote:Disconnect everything from psu. Turn it on and attach multimeter. Use the dial to set 5v on the psu. I don't know what the percentage is here...but you can get away with something like 5.05

Sent from my LG-H811 using Tapatalk

10-4, Thanks!


Reply
Page 1 / 3
Share: