Increasing distance...
 
Notifications
Clear all

Increasing distance between smart pixels.

5 Posts
4 Users
0 Reactions
2,170 Views
CUTTHEMUSIC
Posts: 51
Topic starter
(@cutthemusic)
Trusted Member
Joined: 14 years ago
[#23939]

I'm new to RGB and for next year I'm looking to get about 200-300 of Ray Wu's smart pixels for next year. I believe the spacing between each pixel is a few inches but I need about 2-4 feet between each pixel. I know I could splice wire in between each pixel to increase the distance between them but my concern is with voltage drop, data loss etc due to the increase in distance. If I do this what do I need to be concerned with? How many pixels can I run together if the average distance between them is 3 feet? Do I feed power from both side, middle etc??


4 Replies
Posts: 1249
(@jstjohnz)
Noble Member
Joined: 17 years ago

I would suggest that you go with a 12V pixel such as the 1804, and have them built with 18 gauge wire. There's a voltage drop calculator on here somewhere that may help you verify the configuration. The data is regenerated at every pixel, so the only concern would be voltage drop.


Reply
Posts: 252
(@vincerules)
Reputable Member
Joined: 14 years ago

You could also send Ray a message and get a quote on a custom string of pixels with the spacing you are looking for. Ask him using metric measurements to reduce any possible confusion.


Reply
Posts: 183
(@buckanear)
Estimable Member
Joined: 15 years ago
CUTTHEMUSIC wrote:I'm new to RGB and for next year I'm looking to get about 200-300 of Ray Wu's smart pixels for next year. I believe the spacing between each pixel is a few inches but I need about 2-4 feet between each pixel. I know I could splice wire in between each pixel to increase the distance between them but my concern is with voltage drop, data loss etc due to the increase in distance. If I do this what do I need to be concerned with? How many pixels can I run together if the average distance between them is 3 feet? Do I feed power from both side, middle etc??

WS2801 pixels can be spaced easily up to 3meters (~10 feet) and keeping the data rate to the string at or below 2Mhz.

As for the power lines that depends on how many pixels are on the string. If you are doing say ten pixels, then I would say to use 18 gauge wire for power and ground.

The best way to calculate the total voltage drop is to add up all the drops between the pixels to the last pixel. So lets say you have N pixels. N is the total number of pixels.

Wire resistance is a table lookup. Either from an Amateur Radio Handbook or from the web by searching AWG. See here http://www.powerstream.com/Wire_Size.htm .

basically
20 gauge will have 0.010150 Ohms per foot.
18 gauge will have 0.006385 Ohms per foot.
16 gauge will have 0.004016 Ohms per foot
14 gauge will have 0.002525 Ohms per foot.

So with 3 foot spacing

20 gauge will have 0.03045 Ohms
18 gauge will have 0.01916 Ohms
16 gauge will have 0.01205 Ohms
14 gauge will have 0.00758 Ohms

Now with 50 pixels we start with the first two and say 18 gauge wire

(50-1)*.06*.03045 = 89.5mV drop
(50-2)*.06*.03045 = 87.7mV drop

just after the second pixel you have already lost 177mV from a 5.0VDC source. Each subsequent section will drop about 1.8mV less. That is when all 50 pixels are on full and white light generation.

I personally would not recommend more than ten with three feet spacing unless you plan to go to 14 or 12 gauge wire for power and ground and 5VDC. In the above example with 14gauge wire will start off with 22mV drop between the first and second pixel. Each inter pixel drop will lower by 0.5mV per stage. Even with 14 gauge and 50 pixels you are already at a 500mV drop near the 20th pixel or so. The best case voltage drop allowed to the last pixel for a 5VDC system would be about 750mV max. Probably more likely 500mV drop would be tolerable.

I plan this year to use WS2801 pixels I have for luminaries. I plan to use 18 gauge wire or 16 gauge landscape wire for power between the pixels. I also will use 12 gauge landscape wire from the power supply. I planning on four ten light strings with 3 feet spacing. The clock and data will be 22gauge twisted pair.

Right now the push is to the WS2811 driver chip. basic reason is the output transistors inside the driver chip can handle 12VDC as opposed to 7VDC for the WS2801. The WS2811 is more suited to operate off of 12VDC strings as only the red led will need a current limiter resistor inline. As with the WS2801 will need a series resistor in the blue and green led lines which essentially defeats the advantage of going from 5VDC to 12VDC. So if you are using large number of pixels per strings then you are better off with the WS2811 strings and 12VDC with 3 foot separation.

hope this helps

james


Reply
Posts: 183
(@buckanear)
Estimable Member
Joined: 15 years ago
vincerules wrote:You could also send Ray a message and get a quote on a custom string of pixels with the spacing you are looking for. Ask him using metric measurements to reduce any possible confusion.

With 3 to 5 foot separation yes data and clock are not a real issue if you slow down the clock and data rate enough. You are just not going to clock them at the 25MHz rate as per the spec.

james


Reply
Share: