pixelpuppy wrote:What is the spacing between the drops and number of pixels per drop?
There are 10 pixels per drop, cut from a 5m strip of 5V WS281X 30 LEDs/m so it gives 15 icicles from each 5m strip. Horizontal spacing is about 3.2" between drops for icicles facing the viewer, which uses 30 drops (2 total 5m strips) per 8' section. This gives an aspect ratio of about 2.5:1 and makes text readable. You can do 2 lines of text with a 5x5 font or 1 line of text with larger font, or short graphics. Icicle sections receding from view are triple-spaced (approx 10" between drops) which looks closer due to the viewing angle.
I didn't ever write it up. I should do that. :blush: Here are a few close ups:
BTW, those little PCB-ettes at the end of the icicles are here:
https://oshpark.com/users/current.523bd96f4bca6afb500007c5
although you might be able to use something like this:
https://www.aliexpress.com/item/100pcs-4-pin-LED-Connector-T-Shape-For-10mm-5050-RGB-LED-Strip-Single-Color/32787664467.html
don
Skunberg wrote:Don Julian did a great job above.
thx!
Skunberg wrote:There is a factory solder joint every 15 (1/2 meter) so it's just desolder the joint and it's already tinned for wiring.
I ran into that a lot and it was really annoying. I ended up cutting off the very first pixel, then cutting every 10th, then solder that very first pixel onto the end of the last icicle (which only had 9 pixels left). This way, I only had to deal with it 1x for each 5m roll, rather than 10x.
don
Hi Don,
I have yet to build my icicles, but was thinking of using bullet nodes instead of strips for ease of repair. Was just wondering if you have had any problems with failures? and if so what was the failure rate?
Thanks
Mick
mickr wrote:Was just wondering if you have had any problems with failures? and if so what was the failure rate?
The RGB icicles contain 2,070 pixels, and I had the very first failure this past season (4th year of using them). The failure appears to be at one of those solder joints between the pixels rather than within the actual pixel itself. To be fair, I only put them up for about a month out of the year and there were a couple of rather dry winters, but it did actually rain some and there was often dew built up on them at other times. This past season I finally had the courage to run them in the rain one night and they worked without problem (except for that area affected by the one bad joint).
I also have a garage door grid containing 768 pixels. That has been up for 3 years continuous (I don't take it down) and again this past season I had the first failure - this was at the end of a strip and the strip started to separate a little due to moisture over the years. (I leave the silicon tube open at the ends, so it is not air-tight).
By comparison, I have a pixel tree containing strings of the square epoxy filled WS2811 pixels (about 1,100 or so pixels) which are equivalent to the bullets (jumbo LED + WS2811 chip on a tiny PCB) except for the shape, from my understanding. I've had it for 4 seasons now and I've had to replace 1 failed pixel in 2 of those years even though I put extra silicon on the backs of those that appeared to need it. During rain it flickers and partly goes out, and sometimes still flickers for a day or so after - it seems to require more than a day to "dry out" after it has rained, but then it seems to be fine again.
I live in S. CA where we get some rain, often dew, but not freezing temps. For my environment, I have found the WS281X LED strip enclosed in silicon tubing to be more reliable than the (square) bullet pixels with wires coming out the backs of them. (All were from Ray Wu). I probably did not moisture-proof the pixel strings in the tree as much as I should have, but the icicles and garage door grid required no extra weather proofing. But, as they say, YMMV.
(I will try to get the icicle construction technique written up in the next few weeks. I was uncomfortable doing that until I knew how well it withstood weather, but I think I have a reasonably good view of that now).
don
Really nice work Don. I showed my wife and she loved them. I'm in Riverside and occasionally drive to OC. If I'm in the area next season I'll have to drive by and catch the show. 🙂
Sent from my iPhone using Tapatalk



