Help picking out Pi...
 
Notifications
Clear all

Help picking out Pixel types

14 Posts
8 Users
0 Reactions
4,017 Views
Posts: 16
Topic starter
(@bz-mikeh)
Eminent Member
Joined: 11 years ago
[#42275]

Hi everyone,
Noobie here, first year making a pixel tree. I'm having a hard time on deciding on what type to go with. Is there an advantage/disadvantage of going with the node over strips? I have already picked up a falcon controller to use with these.


13 Replies
Posts: 944
(@didjareally)
Noble Member
Joined: 12 years ago

I recommend nodes, simply because repairing strips is a pain in the backside. If a node goes out, cut it out and splice in a new one. If a pixel in a strip goes out, you have to cut the weatherproof silicone, pull it back, cut out the pixel and splice in a new one, then figure out how to patch the silicone back together and weatherproof it. Doing this on a bench, not so bad, doing this is cold weather while mounted to the house or a prop, quite bad.


Reply
stallionent
Posts: 1460
(@stallionent)
Noble Member
Joined: 13 years ago

I agree, nodes. My house outline is strips, thinking of changing to nodes, 12 volt not 5 volts, I hate power injection.


Reply
Posts: 4092
(@skunberg)
Famed Member
Joined: 18 years ago

Welcome to DIYC!!! Don't limit yourself. Some things work better with nodes and other things work better with strips. Sometimes 5v works good and other times 12v is easier. Figure out what you want to build. Then look at a few videos to see how others have done it. Then your ready to ask some questions.


Reply
Posts: 16
Topic starter
(@bz-mikeh)
Eminent Member
Joined: 11 years ago

Thanks for the comments guys. I'm looking at building a 12 string tree around 10ft (not set in stone). I have been messing around with xlights and have even bought a few sequences from people. I like the idea of being able to replace the nodes when they burn out but I'm scared they won't be as clear as the strips? The distance to the road is only about 100ft or so


Reply
Posts: 4092
(@skunberg)
Famed Member
Joined: 18 years ago

For a tree, I would recommend string nodes and James strips to support them. You can pick different spacing up to what your pixel wire spacing will support. With only 12 strings, I would suggest a 180 degree tree or a flat ray type tree. You may want to use your pixel count (or half if folded) and disired spacing to figure a hight for your tree.


Reply
Posts: 16
Topic starter
(@bz-mikeh)
Eminent Member
Joined: 11 years ago

I know ray's site is the most frequent for ordering pixels, for some reason I have a hard time finding stuff on his site. Do you happen to have a link to the best ones to get?


Reply
jnealand
Posts: 956
(@jnealand)
Prominent Member
Joined: 19 years ago
Reply
Posts: 451
(@utimgr)
Honorable Member
Joined: 14 years ago

I'm surprised that nobody is making a node using the PL9823 LED. Its a thru hole 5mm RGB, using the WS2811/2812 protocol. Put this on a board, add a Fresnel lens, dip them in epoxy coating and you have waterproof node.


Reply
Barnabybear
Posts: 1583
(@barnabybear)
Noble Member
Joined: 15 years ago
Is there an advantage/disadvantage of going with the node over strips?

Hi, yes.
Will the tree be flat (ray) or rounded (normal tree style)?
Will it be viewed from one distant postion or from many close postions?
180, 270 or 360 deg?
Do you intend to use it to display video?
Sorry for the questions - and this is just the start to answer your question.


Reply
Page 1 / 2
Share: