Flickering pixels b...
 
Notifications
Clear all

Flickering pixels between segments

43 Posts
14 Users
0 Reactions
12.8 K Views
Posts: 234
(@uzelessknowledge)
Reputable Member
Joined: 12 years ago

Hey dpdigital!
I'm also having flickering issues on subsequent strings. Sounds like it may be similar/same. I see you have "space" between your sets.
I was able to narrow it down to the data was getting corrupt. How you ask? Trial and error. Or so I think tonight. Wait till tomorrow and I may give a different theory.

I have multiple sets of lights (elements) and they have space between them. When that space got ~6+ feet then they would flicker. Reduce the distance and the flickering goes away. You said you have about 8 feet. Have you tried shortening this distance?

I just ordered some of the uAmps and will see if that helps. I hope so.
http://falconchristmas.com/forum/index.php/topic,2442.0.html

https://www.youtube.com/watch?v=lp8QYcV57bo

Travis
Sent from my iPhone using Tapatalk


Reply
Posts: 79
Topic starter
(@dpdigital)
Trusted Member
Joined: 12 years ago
uzelessknowledge wrote:Hey dpdigital!
Have you tried shortening this distance?
http://falconchristmas.com/forum/index.php/topic,2442.0.html

https://www.youtube.com/watch?v=lp8QYcV57bo

Travis
Sent from my iPhone using Tapatalk

Thanks for the heads up uzelessknowledge. I actually have tried shortening the distance. I have two locations where the problem exists right now. The one location between power supply 2 and 3 is my standard pixel spacing of about 10 inches. The other location (the 8 foot gap) is between PS 1 and 2. In that location I tried shortening the gap by adding a few "null" pixels and the problem remained with the strings before and after the null pixels.

I think I have pretty well narrowed it down to having purchased some el-cheap-o PS's with very poor filtering and grounding. At this point I'm planning on returning them as I feel they will be unusable as RobG mentioned earlier. When I hooked up my scope, I saw a lot of noise when isolated and it was interesting how when I connected the scope reference, which is grounded, it seemed to improve on the noise and the flickering reduced. I think I just need to get some decent and reliable grounded power supplies.

Thank you everybody for your input and your help. Great suggestions and feedback very much appreciated!! I will try to update on better results with new PS's.

Dan P.


Reply
Posts: 1133
(@toozie21)
Noble Member
Joined: 19 years ago
Dpdigital wrote:Thanks for the heads up uzelessknowledge. I actually have tried shortening the distance. I have two locations where the problem exists right now. The one location between power supply 2 and 3 is my standard pixel spacing of about 10 inches. The other location (the 8 foot gap) is between PS 1 and 2. In that location I tried shortening the gap by adding a few "null" pixels and the problem remained with the strings before and after the null pixels.

I think I have pretty well narrowed it down to having purchased some el-cheap-o PS's with very poor filtering and grounding. At this point I'm planning on returning them as I feel they will be unusable as RobG mentioned earlier. When I hooked up my scope, I saw a lot of noise when isolated and it was interesting how when I connected the scope reference, which is grounded, it seemed to improve on the noise and the flickering reduced. I think I just need to get some decent and reliable grounded power supplies.

Thank you everybody for your input and your help. Great suggestions and feedback very much appreciated!! I will try to update on better results with new PS's.

Dan P.

I think you've nailed it. To me when all white is the problem, it usually means power supply, it is the most taxing on it. I guess if yoy wanted to proved to you self further, you could always run all white at 25% brightness and see if the flickering goes away...

Short and badly typed since written from my phone...


Reply
RobG
Posts: 1255
 RobG
(@robg)
Noble Member
Joined: 14 years ago

Funny thing, I connected a bunch of pixel floods yesterday and experienced something similar, from time to time one or more pixels were flickering or were showing false color. I could see the problem on the scope, few extra bits where they should not be, very odd. I suspected PS, cables, software. I tweaked my code (which BTW worked great all this time, but I thought that maybe my new setup was little more "sensitive,") I switched PS, added LP filter, nothing helped. I spent a lot of time today trying to get it right. As I was getting ready to wrap it up for today and head to bed, I decided to swap my floods around. Bingo! Turns out the WS2811 in my first flood is faulty and from time to time "leaks" few bits to its output.

Sent from my iPad using Tapatalk


Reply
Posts: 459
(@shockwave)
Reputable Member
Joined: 15 years ago

One idea to consider. You said the flicker only occurs when they are set to white. Are you certain you don't have an additional output set in vixen that is driving the identical section?

If you have an output driving the pixels on and an identical setup driving them off, you'll get flicker. And noting you have separate floods in the middle, you may have an output for the floods and one for the string, even though they are really all one thing and should be addressed as one thing.


Reply
Page 4 / 9
Share: