F48 & Smart Receive...
 
Notifications
Clear all

F48 & Smart Receivers

5 Posts
5 Users
1 Reactions
1,306 Views
Posts: 427
 munu
Topic starter
(@munu)
Honorable Member
Joined: 6 years ago
[#58232]

I am reading the manual (again) about the F48 and the smart differential controllers (I'll call them SDR in this post). I am not quite sure how to configure the SDRs and use the F48. The F48 has 3 banks/rows (top, middle, bottom) of 4 Ethernet connectors. So 12 Ethernet ports. Each of those 4 Ethernet connectors in one bank can support ONE SDR, each of which has 4 ports. Hence 12 Ethernet ports * 4 ports per SDR = 48 ports (so F48). Now, each of those SDRs have an Ethernet input and an Ethernet output to daisy-chain SDRs. If I interpret the manual correctly, you can use the "Mode Switch" DIPs to say where an SDR is located. My understanding is that "Normal Mode" means the SDR is the first SDR that is directly connected to an Ethernet port on the F48. Then if you daisy-chain an SDR to that first SDR, you put the "Mode Switch" to "Smart - A" on that first daisy-chained SDR. Then when you daisy-chain the "Smart-A" SDR to another SDR you set the DIP switches on that SDR to "Smart - B". Then, when you daisy-chain the "Smart-B" SDR to another SDR you set the DIP switches on that SDR to "Smart - C". That's where it ends. You can only daisy-chain 4 SDRs together. That's because you only have 16 ports per bank (again, with 3 bank giving you 48 port). On all but the last SDR you set the 4 terminator DIPs to OFF (two DIPs with two switches in two different places...). On the last SDR, you set all 4 switches to ON (which they are by default). So don't get confused by those total of 4 switches. They are either all on or all off. Did I understand this correctly, so far?

Now my real question is, what Ethernet ports can I use on the F48. Assume I connect Ethernet port 1 on bank 1 to SDR 1. SDR 1 has 3 other SDRs daisy chained. So that's 16 ports and I used up bank 1. Now I have to go to bank 2 for the next SDR.

But how about if the first SDR only has 1 daisy-chained SDR. So 2 SDRs making up 8 port. Do I now plug in the next SDR to Ethernet port 2 on bank 1 (all 1-indexed) or do I plug the next SDR into Ethernet port 3 on bank 1 because Ethernet port 1&2 take up port 1-4 & 4-8?

How about if I just use 6 ports on the first 2 SDRs instead of all 8? Am I just wasting those two ports? Or could I terminate the second SDR at "Smart - A" and then plug in an Ethernet cable on Ethernet 3 bank 1 and set the first SDR to "Smart - B"?

https://docs.google.com/document/d/1-ei5l6h9wltfD4pZ0Jox6chTYPKULPf1GhA6VWT-qCA/edit


4 Replies
Posts: 429
(@mikekrebs)
Reputable Member
Joined: 12 years ago

Someone with a F48/SDR will have to answer the real question but just need to correct the terminology so there is no confusion. The F48 uses differential outputs - not Ethernet. The jacks look like common network ports and you connect them using a common network cable called cat5/6/7. But the outputs are not Ethernet. And (according to the manual), you should be very careful not to plug the SDR into an actual network port (Ethernet) because you could damage the boards.


Reply
Posts: 281
(@bert-nc)
Reputable Member
Joined: 18 years ago

watch the you tube videos from
Listen to our Lights by John Storm I believe
He has made several videos that I think will help you


Reply
ChiefWarrant
Posts: 570
(@chiefwarrant)
Honorable Member
Joined: 19 years ago

I haven't used a Falcon controller in a while and am not claiming to be an expert, but you should think more along the lines of Pixels per port and not the number of ports.

I would assume that Falcon has changed their GUI (web interface) to reflect the addition of smart receivers. I use Experience controllers and I can simply add the number of smart receiver "ports" down what ever daisy chain i am using. You may have the ability of assigning a certain number of "ports/pixels" the same way.

So on the "1-4" port of the controller I can send however many pixels I want down that physical port and in the GUI, just define it as a stacked smart receiver. So if I have 4 smart receivers daisy chained on the port labeled "1-4," one may think that I am actually terminating 16 "ports" on a physical interface, but I am not. I am sending pixel data down the line and allowing the smart receivers to sort it out.

I am assuming the labels of 1-4/2-8/9-12/etc lables are just vestiges from the days before smart receivers existed. So you were limited to that many "ports" per RJ45 8P8C connector. The introduction of smart recievers changed this. But you still have the limitation of 1024 pixels per RJ45 8P8C connector. How you divide those 1024 pixels is up to you.

As @MikeKrebs pointed out, terminology is important. If I remember correctly, the F48 ports output RS485 (or similar signaling) to the receivers. It is definitely not Ethernet. There is the very real possibility of damaging something if you send the wrong voltage down a line.


Reply
Posts: 75
(@mark-m)
Trusted Member
Joined: 3 years ago

In 3 images from this post it should give you a reasonable idea what banking and chaining of SRx's mean.



Banking concepts from the F16v3 is the exact same for the F48.
Difference is the F16v3 only has bank 1 installed on the board, banks 2 and 3 are expansion boards.
https://www.youtube.com/watch?v=4SEVDlZ2CI4


Reply
Share: