ESPixelStick Univer...
 
Notifications
Clear all

ESPixelStick Universe question

33 Posts
14 Users
0 Reactions
13 K Views
Posts: 144
Topic starter
(@drewdennis)
Estimable Member
Joined: 9 years ago
[#47656]

I have a question I can't seem to google an answer for. I read that the ESPixelStick can control 4 universes. How? Do I wire 2 strings with common power but separate data pins? Or is it a "logical mapping",,, It may be out there and I just cant find the info---its also possible I am asking the question wrong or looking at it incorrectly....again...I AM a newb at this!
Looking forward to getting 2 more strings in along with another ESPixelstick...if amazon can find where they lost it. UGH.

Thanks in advance!

PS - a thought / question. Any chance of an external antenna connector on the next model?


32 Replies
sporadic
Posts: 1199
(@sporadic)
Noble Member
Joined: 14 years ago

It's up to 680 pixels, but only one output. They'll act like one long string spanning multiple universes. A model with external antennas is not planned at this time, however someone could make an ESP-02 or ESP-07 (which does) adapter board with ESP-01 headers. Should be an easy project to layout.

Sent from my Moto G (5) Plus using Tapatalk


Reply
Posts: 144
Topic starter
(@drewdennis)
Estimable Member
Joined: 9 years ago
sporadic wrote:It's up to 680 pixels, but only one output. They'll act like one long string spanning multiple universes. A model with external antennas is not planned at this time, however someone could make an ESP-02 or ESP-07 (which does) adapter board with ESP-01 headers. Should be an easy project to layout.

Sent from my Moto G (5) Plus using Tapatalk

Thanks! Lots more to learn! 🙂


Reply
jchuchla
Posts: 8698
(@jchuchla)
Illustrious Member
Joined: 15 years ago

always remember, strings and universes have nothing to do with each other. Some older controller designs had some restrictions on how universes were distributed across string outputs, but that's due to hardware limitations on the controller itself, or simply for convenience for the people writing the firmware.

A universe is nothing more than a group of 512 channel values.

A string of pixels can really be any number of pixels. But for practical purposes, it's considered that around 680 is the practical limit because of the speeds we need for sequencing.

Are you ever going to use 680 pixels on an ESPixelStick? I haven't even come close. But i don't usually use the 400+ horsepower in my pickup truck either. It can actually do it, and it looks great on a spec sheet, but it's not something most people actually need.


Reply
Posts: 693
(@davdue)
Prominent Member
Joined: 19 years ago
DrewDennis wrote:I have a question I can't seem to google an answer for. I read that the ESPixelStick can control 4 universes. How? Do I wire 2 strings with common power but separate data pins? Or is it a "logical mapping",,, It may be out there and I just cant find the info---its also possible I am asking the question wrong or looking at it incorrectly....again...I AM a newb at this!
Looking forward to getting 2 more strings in along with another ESPixelstick...if amazon can find where they lost it. UGH.

Thanks in advance!

PS - a thought / question. Any chance of an external antenna connector on the next model?

So let me see if I understand this correctly. I could have one long string of 680 pixels with 170 pixels on each of 4 universes tied to one ESPixelStick. If I have more than 680 it's another ESPixelStick starting at pixel #681?


Reply
Posts: 376
(@gnarmstr)
Reputable Member
Joined: 13 years ago
davdue wrote:So let me see if I understand this correctly. I could have one long string of 680 pixels with 170 pixels on each of 4 universes tied to one ESPixelStick. If I have more than 680 it's another ESPixelStick starting at pixel #681?

That is sort of true, I have recently been told that there really is no limit to the number of pixels or Universes for the ESPixel. The limit would be determined by how low you want the refresh rate. If you run your show at 50ms then I think you could have 1360 pixels over 8 universes.


Reply
Posts: 693
(@davdue)
Prominent Member
Joined: 19 years ago
Gnarmstr wrote:That is sort of true, I have recently been told that there really is no limit to the number of pixels or Universes for the ESPixel. The limit would be determined by how low you want the refresh rate. If you run your show at 50ms then I think you could have 1360 pixels over 8 universes.

Hmm interesting. I have always ran my Vixen V2 sequences at the default of 100ms. I assume then you would spilt the 1360 up into 4 equal universes.

With that thought I should be able to run the following on 3 ESPixelSticks

Yard Lights (8 incand strings) ->2 pixel strings to replace each incand -> 100 pixels -> 32 total pixel strings -> 1600 pixels
Driveway Lights (4 incand strings) -> 4 pixel strings -> 200 pixels -> 24 total pixel strings -> 1200 pixels
Garage Lights (1 incand strings): 4 total pixel strings -> 200 pixels

What do you guys typically run your refresh rate at? Is that a setting in the E1.31 plugin?

Sent from my iPhone using Tapatalk


Reply
Posts: 1592
(@ruppro)
Noble Member
Joined: 11 years ago
davdue wrote:Hmm interesting. I have always ran my Vixen V2 sequences at the default of 100ms. I assume then you would spilt the 1360 up into 4 equal universes.

What do you guys typically run your refresh rate at? Is that a setting in the E1.31 plugin?

Sent from my iPhone using Tapatalk

No, a Universe is a fixed max of 170 pixels (well 170 2/3 or 512 channel) so the 1360 would be 8 universes


Reply
jchuchla
Posts: 8698
(@jchuchla)
Illustrious Member
Joined: 15 years ago
davdue wrote:So let me see if I understand this correctly. I could have one long string of 680 pixels with 170 pixels on each of 4 universes tied to one ESPixelStick. If I have more than 680 it's another ESPixelStick starting at pixel #681?

No, you're thinking of it as if pixels are tied to universes. They're not, pixels are 3 channels. Multiply pixels by 3. Then divide by 512 to figure out how many universes it takes to send that many channels.
So for your example, You would have a string of pixels that takes 2040 channels. You need 4 universes It would use all 512 channels of the first 3 universes, and 504 channels of the 4th universe. You could actually drive 682 pixels with just under 4 universes. (3U+510C)
If you have two things that are 10 inches long and you add them together, you get 20 inches which is equal to 1 foot 8 inches. It's not equal to 2 feet. Same concept applies here.

I don't think there's a hard limit on the number of channels an ESPixelStick supports. At least there wasn't in previous versions, but there may be a hard limit now in 3.0. I haven't tested recently. I never use nearly that many anyhow. Most of mine only have a handful of channels in use. A few have something under 2 universes worth on them. Personally i don't like the idea of that many pixels on a single controller. That's putting too many eggs into a single basket for my liking.

I always forget the actual number every time this conversation comes up, but if i recall last time i did the math it's in the 800 pixel range for 50ms sequence timing which is why 680 is often used as a reasonable limit. So if that limit still is wide open on an ESPixelStick, you could keep going past the 680 until you either run out of memory in the ESP or it's too slow for your liking.


Reply
sporadic
Posts: 1199
(@sporadic)
Noble Member
Joined: 14 years ago

There's a hard limit set for 8 universes / 1360 pixels and that takes 40.85ms to generate for ws2811 pixels. It's advertised as 4 universes / 680 pixels as that's roughly the max for a 25ms show rate. The most I've ever tested with is 720 pixels, but I've had reports from other users running more than that. If you really want to get crazy, you can edit the code, remove the limit - https://github.com/forkineye/ESPixelStick/blob/master/ESPixelStick.h#L60 however the refresh rates would be VERY slow and it'd probably look like crap. I personally use a 25ms show rate as 50ms looks choppy to me on may faster effects.


Reply
Page 1 / 4
Share: