Shouldn't your start channel be #5:1
Can you post your controller comfiguration
keithsw1111 wrote:Shouldn't your start channel be #5:1
Good catch Keith. Looks like he had that selected as absolute channel number and probably forgot to change it when he specified Universe #.
keithsw1111 wrote:Can you post your controller comfiguration
Hi Keith,
Thanks for your input, checking the config page of the ESPixelstick I found my error, "finger trouble" 🙁 - fixed now!!
Regarding the start channel setup, once the config was corrected it worked fine as it was, you suggested changing the addressing a little while back, I have now done that and the start channel box now displays :- #192.168.200.50:5:1 and the preview appears fine. Silly question now from me, is that the way it should be ?? "Newbie Question" I know, says he at close on 74!!!
I was absolutely sure I had set the ESPixelstick's to a 510 channel universe, but on second checking they were sitting on the default of 512, sorry Shelby for giving you the wrong information, it must have been late night bleary eyes here.
Thanks heaps to you to all for your assistance, at this busy time of the year, I am totally unfamiliar with the universe concept, hence my cry for help. Using ESPixelstick's for the first time, and Xlights to drive them, also for the first time, I am well aware that there are a number of areas/boxes in the setting up areas that I could make a mistake in by inputting incorrect data far too easily.
For future reference, in simplistic terms 🙂 ?? why did the 2 channel universe barrier error in the ESPixelstick config completely upset all the rest for the channels on that controller ??
A test run in daylight the setup appears fine now 🙂 I will confirm later, 10 hrs or so from now.
Thankyou one and all once again for your help, all the best for your own shows this year,
Terry
RichD wrote:Definitely sounds like a 510 v 512 universe size issue somewhere. Though Xlights channel numbers look ok and you had said the pixelsticks were set to 510. Odd. Can only think to restart it all to see if anything changes, maybe something is showing a different value to what it is using.
Thanks RichD,
As you will see below, you were correct, "Finger Trouble and Bleary Eyes" I suspect. 🙁 Once I changed the setting to 510, the problem appears to have gone away!!! Time will tell later when it is dark - 10 hours or so.
Thanks heaps for your help,
Terry
MikeKrebs wrote:data is output for example rgbrgbrgbrgb...
this continues uninterrupted through whatever is defined. When we get to byte 511, r is sent, then at 512 g, then the next universe picks up and byte 1 is g so in universe 2, the pattern is grbgrbgrb. if this doesn't match what the controller expects (ie it expected data to stop at byte 510), you get the change in color you experienced. So both the sender and receiver need to know what is expected for the cutoff of a universe of data.All of this behavior is because the E1.31 uses DMX which had 512 as "more than you would ever use".
Brilliant, thanks MikeKrebs, that makes perfect sense 🙂
I am suitably chastised for not inputting the correct numbers in the first place, I will certainly be double/triple checking the numbers from now on!! I do not like raising problem hassles when everyone is busy with their own shows.
Cheers,
Terry
Quick report back, 100% success after a test run in the dark, everything is looking great 🙂 Once more thanks for the fantastic help from everyone, only one problem now, it is really "too bright", I think I will have to find out how to throttle the brightness down a bit!! 🙂
Terry
Glad you're sorted. For brightness if you go to the layout tab in xlights you can select a model then choose dimming curves in it's properties and reduce its brightness there. (As the gamma correction on the espixelstick is applied after that change you might not need to make as big a reduction as some people might quote)
RichD wrote:Glad you're sorted. For brightness if you go to the layout tab in xlights you can select a model then choose dimming curves in it's properties and reduce its brightness there. (As the gamma correction on the espixelstick is applied after that change you might not need to make as big a reduction as some people might quote)
Fantastic, I was just about to "go digging" to find out how to do that 🙂 There are so many places to "fiddle" with settings in xLights that I am rather hesitant at this late stage to tread amongst those "unknown to me" in case I create another problem to which I do not know the cure!! "See Below"!! 🙂
Cheers, Terry

