Espixelstick - Esp3...
 
Notifications
Clear all

Espixelstick - Esp32 - maximum led

23 Posts
4 Users
0 Reactions
6,856 Views
MartinMueller2003
Posts: 7614
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

I have:

Input = effects - random
Output ports 1,2,3 each with 1000 pixels.
UI is working fine. Watching diagnostics screen with no issues. Console shows no errors.


Reply
MartinMueller2003
Posts: 7614
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

And this morning it is still running. Now to test receiving data via the E1.31 interface.


Reply
MartinMueller2003
Posts: 7614
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

E1.31 multicast up to 9000 channels (3000 pixels) works. Lots of lag but the device does not crash or drop off the network.

Thanks to the OP I did discover a bug in the E1.31 setup functions that will truncate and delete anything over 5000 channels (~1600 pixels) of data. A fix for this has been pushed to my branch and should go to Shelby's branch soon.


Reply
MartinMueller2003
Posts: 7614
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

Same test repeated with 6 outputs at 500 pixels per output. MASSIVE lag in the network and UI but the ESP did not drop off the network. I would say that the ESP32 with 3000 channels is NOT going to work well using E1.31. It does seem to have no issues when playing from a local file so this would be just fine for Remote FPP use which is better for your network anyway.


Reply
Posts: 167
 gb70
Topic starter
(@gb70)
Estimable Member
Joined: 6 years ago

thanks for all the tests you are doing, Martin
actually I'm still going with E1.31 Unicast ... I'm not ready for the multi yet
I got home now and immediately tried to insert 500 pixels for the first three outputs .....
I must say, with surprise, that now the esp32 remains permanently connected .... with surprise because yesterday I tried it as a first attempt.

at the weekend I take all the strings and connect everything ... and I'll see if the pixels will be fine too

i really don't know what could have happened ... only thing i did yesterday before closing everything, was to reload the firmware .jar file

while I was saving in the firmware I left the serial monitor of the Arduino IDE active and I noticed these strings ... I don't know if they can cause other problems


[FileMgr] Configuration File: '/config.json' saved 327 bytes.
[FileMgr] Configuration File: '/config.json' loaded.
[FileMgr] Configuration File: '/input_config.json' saved 957 bytes.
[FileMgr] Configuration File: '/input_config.json' loaded.
[  E1.31] ERROR: Universe configuration is too small to fill output buffer. Outputs have been truncated.
[FileMgr] Configuration File: '/output_config.json' saved 4463 bytes.
[FileMgr] Configuration File: '/output_config.json' loaded.
[  E1.31] ERROR: Universe configuration is too small to fill output buffer. Outputs have been truncated.
[  E1.31] Listening for 4500 channels from Universe 1 to 15 on port 5568
[  E1.31] ERROR: Universe configuration is too small to fill output buffer. Outputs have been truncated.

Reply
MartinMueller2003
Posts: 7614
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

I had those same errors and have posted a fix. That is an indication that the internal list of universe translations is too small. That has now been fixed. Next time Shelby takes a pull from my branch, the fix will be in it.


Reply
Posts: 5
(@garymueller)
Active Member
Joined: 8 years ago

Thanks. Those are impressive benchmarks for the ESP32. DDP may give you better performance (less overhead) than E131. I have a few ESP32 coming later this week that I was going to try out.


Reply
MartinMueller2003
Posts: 7614
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

yes


Reply
Posts: 167
 gb70
Topic starter
(@gb70)
Estimable Member
Joined: 6 years ago

this morning I tried but unfortunately I encounter the exact same problem.
I don't understand why it's so unstable.

even I can no longer configure more than 500 pixels per output.

I connected the ESP to the arduino IDE and on the monitor it gives me this error


Rebooting...
ets Jun  8 2016 00:22:57

rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
load:0x3fff0030,len:1100
ho 0 tail 12 room 4
load:0x40078000,len:12280
ho 0 tail 12 room 4
load:0x40080400,len:3076
entry 0x400805ec

[    ESP] ESPixelStick v4.0-ci1482881108 (Nov 19 2021 - 21:58:10)
[    ESP] v4.4-dev-2313-gc69f0ec32
[FileMgr] Flash file system initialized.
[   354][E][sd_diskio.cpp:126] sdSelectCard(): Select Failed
[   354][E][sd_diskio.cpp:790] sdcard_mount(): f_mount failed: (3) The physical drive cannot work
[   657][E][sd_diskio.cpp:126] sdSelectCard(): Select Failed
[FileMgr] No SD card installed
[FileMgr] Configuration File: '/config.json' loaded.
[FileMgr] Configuration File: '/output_config.json' loaded.
[FileMgr] Configuration File: '/input_config.json' loaded.
[  E1.31] ERROR: Universe configuration is too small to fill output buffer. Outputs have been truncated.
[WiFiMgr] WiFi Entering State: Connecting Using Config Credentials
[WiFiMgr] Using DHCP
[WiFiMgr] Connecting to 'home' as home
[WiFiMgr] WiFi Entering State: Connected To AP
[WiFiMgr] Connected with IP: 192.168.1.154
Guru Meditation Error: Core  1 panic'ed (StoreProhibited). Exception was unhandled.

Core  1 register dump:
PC      : 0x4008a960  PS      : 0x00060330  A0      : 0x800eb03b  A1      : 0x3ffd79a0  
A2      : 0xbaad5678  A3      : 0x3ffe9f90  A4      : 0x0000005c  A5      : 0xbaad5678  
A6      : 0x00000000  A7      : 0x00000000  A8      : 0x00000000  A9      : 0x3ffd7960  
A10     : 0x00000001  A11     : 0x3ffb2e80  A12     : 0x00000000  A13     : 0x00000000  
A14     : 0x00000000  A15     : 0x00000000  SAR     : 0x00000017  EXCCAUSE: 0x0000001d  
EXCVADDR: 0xbaad5678  LBEG    : 0x4008a95c  LEND    : 0x4008a972  LCOUNT  : 0x00000004  


Backtrace:0x4008a95d:0x3ffd79a00x400eb038:0x3ffd79b0 0x400eb06f:0x3ffd79d0 0x401232fe:0x3ffd79f0 0x401235e2:0x3ffd7a20 0x40122f91:0x3ffd7ab0 0x40122ffe:0x3ffd7b50 




ELF file SHA256: 0000000000000000


is there a more updated espixelstick firmware (file .jar), to try?
I currently have 4.0 ci 1482881108 del 19/11/21

thanks


Reply
Posts: 167
 gb70
Topic starter
(@gb70)
Estimable Member
Joined: 6 years ago

an info, I got, urgently, 2 ESP32 from amazon. ESPpixelstick, can I load it immediately from the .jar file or do I have to go around with IDE arduino?


Reply
Page 2 / 3
Share: