ESPixelStick - E1.3...
 
Notifications
Clear all

ESPixelStick - E1.31 WiFi Pixel Controller

948 Posts
178 Users
0 Reactions
503.7 K Views
Posts: 2507
(@mrgrumpy)
Famed Member
Joined: 12 years ago
Kev7274 wrote:I got around to using one of the power supplies today and noticed that my pixels were glowing a little. I don't see a way to adjust the power like I do on my big power supplies. Have
you had any issues?

no issues, and my voltages are in the range of a wall wart - what voltage are you reading. Glowing pixels are not normally from a slightly under or overvoltage wart. What V unit are you having issues with and what are you using for a controller.


Reply
Kev7274
Posts: 2037
(@kev7274)
Famed Member
Joined: 13 years ago

I used the 12v 3A ps version that I pictured in the previous post. When I hook everything up,the pixels dim Red. I was thinking that maybe I had a bad string,but I tried 5 different sets and it did the same thing.
I then hooked up my 12v 60W 5A switching power supply and they were fine.


Reply
Posts: 2507
(@mrgrumpy)
Famed Member
Joined: 12 years ago

I would say to go back to the supplier and ask them to provide another one, that you got a defective one.
I got 2 of the 12V and I just retested both on a 96 LED strip (roll missing 56 [3 x 14)
That should equate to 40-45W or more than 3A and they were bright white.

PM me if you need more, or start a new thread....this is off topic.


Reply
Posts: 911
(@madsci1016)
Noble Member
Joined: 12 years ago
Kev7274 wrote:I used the 12v 3A ps version that I pictured in the previous post. When I hook everything up,the pixels dim Red. I was thinking that maybe I had a bad string,but I tried 5 different sets and it did the same thing.
I then hooked up my 12v 60W 5A switching power supply and they were fine.

Dim red pixels are a function of the design of the pixel. They can't tolerate over voltage, sometimes even if it's only 1-2% over 12V. Many vendors have changed the design of the 12V pixel (like DIYLEDExpress) to fix this, and now their 12V pixels can take 7V to 24V with no issues. But some still sell the old design that can't tolerate 12.1V.

With a precise DMM, I bet you'l find the 3A supply is slightly higher voltage than the 5A supply.


Reply
Posts: 2507
(@mrgrumpy)
Famed Member
Joined: 12 years ago

....forgot about the overvoltage PINK issue. My PS is reading 12.47V therefore a 4% over volt situation. Lucky for me I don't have any of those pink pixels.


Reply
Kev7274
Posts: 2037
(@kev7274)
Famed Member
Joined: 13 years ago

Going to try the other PS and see what happens. I'll check the voltage also.


Reply
Posts: 3
(@djgogo2000)
New Member
Joined: 10 years ago

i 've receive today in France the ESPixelStick from the group buy. Thx a lot !!!


Reply
Posts: 17
 Code
(@code)
Active Member
Joined: 11 years ago

Got mine yesterday [emoji636]

Sent from my iPhone using Tapatalk


Reply
Kev7274
Posts: 2037
(@kev7274)
Famed Member
Joined: 13 years ago
Reply
Posts: 6
(@dukethejester)
Active Member
Joined: 10 years ago

Shelby,

One of the supporting members mentioned that you would have another group buy maybe in May. Do you have any of the ESPixelSticks V2 available? I would like to try one. I see the rules that you have to be supporting member. I have been doing the Pi3 with falcon Pi Hat $75 expense for two channel ~2000 pixels. I like the inline solution that is small and Wifi enabled.

DukeTheJester


Reply
Page 52 / 95
Share: