ThinkAgainAgain, where did you get the fused power hub from?
ThinkAgainAgain wrote:I used the pvc glue on the one (lower) end (just cause I had some laying around) I didn't use any glue on the end cap with the ESPixelSticks attached - that cap (upper) - I drilled two holes for my pigtails - one (in) for the power wire and one (out) to pixels. Then I hot glued on the inside and outside around the wires... attached wires to the header plug - so ESPixelSticks are removable if the need arises.So with these hanging outside the rain hits the top wires runs off past the unglued joint and hits the lower glued joint - I didn't want water seeping in from the lower end cap. Friction holds on the top cap.
Sent from my iPhone using Tapatalk
I do mine a little different. I seal the bottom cap, and do not seal the wires. The top cap is pressed on without waterproofing. Water would need to pass the top cap then raise up to get in. And if by some miracle something got in, it could run the walls to the bottom then drain out the wire leads.
Oh, and to service, remove the top cap, push wires up til ESPixelStick is removable. You may need longer leads - so measure before cutting.
rstehle wrote:You have to be a supporting member on this site. Go over to the Green site and you can participate.
I'm on there too with the same name. I just never post as I just read as most of you all have answered questions I've ever wondered. though I searched and didn't see an updated groupbuy for the v2
mrGrumpy wrote:Here you go.....These are salvaged units. You will need to remove the cut off leads and replace with your own.
They are cheap and clean up nicely.
Picture of one I just finished cleaning.They have in 12V too. Gotta order a few of those myself. I like the 3000MA design best.
5V Sample ebay items
http://www.ebay.com/itm/142168265195?_trksid=p2057872.m2748.l2649&ssPageName=STRK%3AMEBIDX%3AIT <<== On Holiday til 1/31/2007
http://www.ebay.ca/itm/AC-DC-5V-2-5A-Switching-Power-Supply-Bare-Board-2500MA-for-Replace-Repair-/331908459278?hash=item4d47492b0e:g:I-YAAOSwAPlXh1W-
http://www.ebay.com/itm/1PC-AC-DC-5-20V-Switching-Power-Supply-Module-for-Replace-Repair-700-2500mA-/262487262001?var=&hash=item3d1d75c331:m:mSehw1EZha1-eYJkYj-V80A12V sample ebay items
http://www.ebay.com/itm/AC-DC-12V-Switching-Power-Supply-Module-0-5A-5A-3A-2-5A-for-Replace-Repair-/351766732567?var=&hash=item51e6ee5f17:m:mCQIrT84mS9_RpdWJXpLXzAMay want to buy some of this larger size heat srink . . . but don't shrink on too tight
http://www.ebay.com/itm/PVC-Heat-Shrink-Tubing-7mm-500mm-lot-Black-/142231468269?var=441298883527&hash=item211da7f8ed:m:mGbDx1Pdf-WiuXjkUVfYHdwOne last work. Many sellers are on Chinese Holiday til 1/31 or some til 2/6
IMPORTANT....One more thing. When you build, do not enter or exit the 120V end with your low voltage. 120V in one side and LV out the other.
Do not cross 120V with 12V leads within the pipe.
What a great find! so i assumed you already tried those in 5V. How many pixels did you power with them? I am planning on 50. Will it be OK?
Regarding your note not to cross the 120V with the low voltage, what is the concern?
Can't wait to give it a try!
-bernard- wrote:What a great find! so i assumed you already tried those in 5V. How many pixels did you power with them? I am planning on 50. Will it be OK?Regarding your note not to cross the 120V with the low voltage, what is the concern?
Can't wait to give it a try!
I measured a 50 stran at just Nader 2A, then connected the 2.5A with a ESPixelStick and ran full white for several hours.
Don't cross 120V . . . I will never route my wires where low voltage crosses high voltage....without an electrical barrier. With this practice, I will never grab a low voltage wire, and get high voltage due to a short. I use this same practice with steel case power supply. HV wires goes one to side and LV wires goes to the other.
mrGrumpy wrote:I measured a 50 stran at just Nader 2A, then connected the 2.5A with a ESPixelStick and ran full white for several hours.Don't cross 120V . . . I will never route my wires where low voltage crosses high voltage....without an electrical barrier. With this practice, I will never grab a low voltage wire, and get high voltage due to a short. I use this same practice with steel case power supply. HV wires goes one to side and LV wires goes to the other.
Just to be clear, you ran a 5 volt 50 pixel strand at full white and got 2 am draw? I was using a theoritical 3 amp value for my pixels and my power supplies had ample extra capacities that I never felt the need to check the actual amp draw.
Thanks for the safety tip on the 120V and LV issue; when you mentioned not running the wires together, my first thought was data deterioration.
I have read through a lot of the thread (and several others) about the debate of unicast and multicast. I get why multicast is more foolproof as it requires no ack but the reduction in number of universes supported not just on this controller but others is substantial. So its a trade off...
I was curious what most people who are using wireless, with this controller or others are using multicast or unicast and what their experience has been? I used unicast and all controllers were wireless (even renard) and once I worked out a few issues it ran rather well (at least when I was watching)! I have looked at what I can do with the hardware I have if I stay unicast versus what it will take to accomplish the same thing multicast and its a big difference.
gocats7 wrote:I have read through a lot of the thread (and several others) about the debate of unicast and multicast. I get why multicast is more foolproof as it requires no ack but the reduction in number of universes supported not just on this controller but others is substantial. So its a trade off...I was curious what most people who are using wireless, with this controller or others are using multicast or unicast and what their experience has been? I used unicast and all controllers were wireless (even renard) and once I worked out a few issues it ran rather well (at least when I was watching)! I have looked at what I can do with the hardware I have if I stay unicast versus what it will take to accomplish the same thing multicast and its a big difference.
I have multiuniverse support via multicast in the dev code, just need to test it.
Sent from my R1 HD using Tapatalk
gocats7 wrote:I have read through a lot of the thread (and several others) about the debate of unicast and multicast. I get why multicast is more foolproof as it requires no ack but the reduction in number of universes supported not just on this controller but others is substantial. So its a trade off...I was curious what most people who are using wireless, with this controller or others are using multicast or unicast and what their experience has been? I used unicast and all controllers were wireless (even renard) and once I worked out a few issues it ran rather well (at least when I was watching)! I have looked at what I can do with the hardware I have if I stay unicast versus what it will take to accomplish the same thing multicast and its a big difference.
The ESPs support the same channel count in either unicast or multicast. Is it some other controller you're using that has this limitation?
Sent from my iPhone using Tapatalk
jchuchla wrote:The ESPs support the same channel count in either unicast or multicast. Is it some other controller you're using that has this limitation?Sent from my iPhone using Tapatalk
I guess I was confused then. I thought the espixelstick supported 1 universe in multicast but 4 in unicast (I know I read this somewhere)? I have seen posts regarding 720 pixels being supported and I assumed that was unicast due to the number. I have several e682s for my pixels and it supports 7 multicast or 12 unicast.
Mainly, just curious what those that have waded into wireless have experienced as its always a trade off to use and the multicast versus unicast is yet another wrinkle. Wondering what others have seen so I can factor that into my decision for how to handle next year. I read your detailed post and it makes perfect sense....but I dont want to waste that much capacity on my e682s unless it is worth it. However, the point of all of this is for peoples enjoyment and visual impact. Jerky, laggy pixels defeats the purpose! I'm in process of planning next year and which direction I go changes quite a bit in the background regarding hardware. I am looking to add a ubiquity AP solely for the SSID I use for my christmas VLAN but if using unicast that doesnt solve it all as the device still has to be close enough to reliably send back the ack.
