michaelc wrote:Will there be the ability to set as starting channel number on this in the near future. I have a bunch of smaller props that I was hoping to have unique ESPixel sticks for and I would need the ability to set a starting channel other than 1.
2.0 version allows you to set starting channel
oceanwanderlust wrote:How many pixels can this thing do?For some reason, I thought it was going to be 4x170=680, but Xlights/Nutcracker seems to be cutting me off at 512 CHANNELS of which I need 3 per pixel so I'm only getting 170 pixels per ESPixelStick. Is this correct?
According to the site it is 4 universes...I have not assembled mine yet to test.
http://forkineye.com/espixelstick-v2-group-buy/
The ESPixelStick supports up to four universes of WS2811 pixels on a single output, or up to 63 GECE Pixels.
oceanwanderlust wrote:How many pixels can this thing do?For some reason, I thought it was going to be 4x170=680, but Xlights/Nutcracker seems to be cutting me off at 512 CHANNELS of which I need 3 per pixel so I'm only getting 170 pixels per ESPixelStick. Is this correct?
I am fairly new with xLights but willing to try and help. You should be able to setup the stick as an E1.31 controller - under the Setup tab click the ADD E1.31 button - I added a 4 universe stick as 192.168.69.73 - see pic below. Can you explain your issue a little further?
I'm having a different problem. It programs correctly and the status window is clear text, but the serial monitor returns only gibberish, so I don't get an IP address. In past experience, that's indicative of differing baud rates, but I'm at115200, 8 data bits, no parity, 1 stop bit, no flow control. Any thoughts on how to correct the output on the serial monitor?
psalmx wrote:Can anyone confirm a bug? I have a strip of pixels with the color order of BRG that I have working fine with an e682. If I plug it in the the espixelstick and change the color order the pixels light up GBR color order.
studiopro wrote:I was doing a quick test with mine using FPP and when I was manually adjusting the colors to turn them on I couldn't get the pixelstick to match either and tried every combo in the pixelstick GUI. I then changed the order in FPP and it worked. However, I didn't try it with any other controller or pixels so my test is complete, but had my head scratching.
I have some BRG strips and they render properly for me. At least I thought they were BRG, lol. The color order assumes pixel data is coming in as RGB, can you verify that's how it set in your sequencers? I don't have my Pi up right now so can't verify via FPP testing myself. The byte offsets for each mode is here.
oceanwanderlust wrote:How many pixels can this thing do?For some reason, I thought it was going to be 4x170=680, but Xlights/Nutcracker seems to be cutting me off at 512 CHANNELS of which I need 3 per pixel so I'm only getting 170 pixels per ESPixelStick. Is this correct?
michaelc wrote:each pixel stick gets assigned a single universe. A si g,e universe is only 512 channel. Since 170 pixels is 510 channels. That is the max pixels per universe and stick
DMJPixel wrote:According to the site it is 4 universes...I have not assembled mine yet to test.
http://forkineye.com/espixelstick-v2-group-buy/The ESPixelStick supports up to four universes of WS2811 pixels on a single output, or up to 63 GECE Pixels.
DMJPixel wrote:I am fairly new with xLights but willing to try and help. You should be able to setup the stick as an E1.31 controller - under the Setup tab click the ADD E1.31 button - I added a 4 universe stick as 192.168.69.73 - see pic below. Can you explain your issue a little further?
Correct, it can do 4 Universes. You can actually do more, but you'll start dropping into unreasonable refresh rates. The most I've tested with is 720 on my test matrix.
michaelc wrote:Will there be the ability to set as starting channel number on this in the near future. I have a bunch of smaller props that I was hoping to have unique ESPixel sticks for and I would need the ability to set a starting channel other than 1.
Coaster wrote:2.0 version allows you to set starting channel
It's there as noted, or was it another function you were looking for?
Kensington wrote:I'm having a different problem. It programs correctly and the status window is clear text, but the serial monitor returns only gibberish, so I don't get an IP address. In past experience, that's indicative of differing baud rates, but I'm at115200, 8 data bits, no parity, 1 stop bit, no flow control. Any thoughts on how to correct the output on the serial monitor?
ESPSFlashTool configures the serial port when programming. What OS are you on? What happens if you hit the reset button on the ESP, do you get any legible text? And lastly, if you have a serial terminal like Putty, could you try it while resetting the ESP? That should help narrow it down.
Windows 10. I saw the parameters the programmer was using to set the serial port coming over the status window, so I figured it might be a baud rate issue. Reset generates gibberish. I tried to PuTTY in, but it doesn't see COM4, which is the USB/Serial cable. That's a problem I've had in the past with various cables. My interim solution is to refresh the wireless router after flashing each ESP-01 and checking the new IP address that shows up. Then I browse to it to verify the stick ID is what it should be.
Kensington wrote:Windows 10. I saw the parameters the programmer was using to set the serial port coming over the status window, so I figured it might be a baud rate issue. Reset generates gibberish. I tried to PuTTY in, but it doesn't see COM4, which is the USB/Serial cable. That's a problem I've had in the past with various cables. My interim solution is to refresh the wireless router after flashing each ESP-01 and checking the new IP address that shows up. Then I browse to it to verify the stick ID is what it should be.
Hmm. Sounds like it could be something with the cable or a driver blocking something. The firmware advertises itself via mDNS as well. You can discover them from an Android phone with this app. Just look for "_e131._udp." and click on it. You'll get a listing of all your ESPixelSticks and IP's by Device ID.
Maybe I'm just not understanding. I was able to use the new flash tool to program all my boards with 1.x with my usb and FTDI board wired up. I then used the same setup to flash everything to 2.0. This version has OTA and I now want to go to 2.1. My understanding is the with OTA I no longer need the FTDI USB setup. What is the process to update and flash OTA using the new .efu?
michaelc wrote:Maybe I'm just not understanding. I was able to use the new flash tool to program all my boards with 1.x with my usb and FTDI board wired up. I then used the same setup to flash everything to 2.0. This version has OTA and I now want to go to 2.1. My understanding is the with OTA I no longer need the FTDI USB setup. What is the process to update and flash OTA using the new .efu?
I'm including the .efu files in the firmware release zip. You just upload them via the admin page and that's it. There are two in the 2.0 release package, one for pixel mode and one for serial mode. Feel free to switch them around and take it for a test drive 🙂



