ESPixel GECE Info T...
 
Notifications
Clear all

ESPixel GECE Info Thread

123 Posts
28 Users
0 Reactions
51.4 K Views
imbluenote
Posts: 1615
(@imbluenote)
Noble Member
Joined: 15 years ago

Is there a reason why though it couldn't run ws2811s? I was planning on using these for a 2811 prop. I have the GECE controllers I could use but if I didn't it could just go in a ta200.


Reply
Posts: 911
Topic starter
(@madsci1016)
Noble Member
Joined: 12 years ago
Heldwhat Christmas wrote:Is the only thing different about the GECE version the form factor?
Assuming I could use one of these for regular WS2811 pixels, I'm thinking of trying one of these inside my 10W floods, and the regular pixel stick is too long. Would be nice to just have a 12v pig tail hanging out and essentially a WiFi flood light.
The inside of the enclosure is about 2.9"x1.9"x1" - would these fit in there? I don't have any CAD viewer software to check the files Bill posted.

The GECE is just a form factor that fits into the GECE box, and does not have direct support for 12V pixels. You have to feed it a regulated 5V. So it wouldn't not be an easy use for your 12V floods, as you would have to fit in a 12V to 5V regulator in as well. Other than that, yes it could drive WS2811 pixels as well.


Reply
imbluenote
Posts: 1615
(@imbluenote)
Noble Member
Joined: 15 years ago

So 5v 2811 pixels? Is there a way to convert the board to handle 12v pixels?


Reply
jklingert
Posts: 1767
(@jklingert)
Noble Member
Joined: 16 years ago

Any thoughts about waterproofing these? The original GECE controller had some sort of epoxy poured into the wire end in the trapezoid shaped cavity to stop water ingress along the wires. Has anyone found the correct screwdriver to take out the triangle shaped screws?


Reply
ukewarrior
Posts: 4674
(@ukewarrior)
Illustrious Member
Joined: 18 years ago

I've been able to use an slotted small electronics screw driver to do the trick.
I wonder if that shape is included in the 'security bit' sets that are sold, like at harbor freight?
http://www.harborfreight.com/33-pc-security-bit-set-68459.html
or
http://www.harborfreight.com/100-pc-security-bit-set-with-case-68457.html

jklingert wrote:Any thoughts about waterproofing these? The original GECE controller had some sort of epoxy poured into the wire end in the trapezoid shaped cavity to stop water ingress along the wires. Has anyone found the correct screwdriver to take out the triangle shaped screws?

Reply
imbluenote
Posts: 1615
(@imbluenote)
Noble Member
Joined: 15 years ago

I know it isn't in the 100 piece set (I have it). I just use a small slotted screw driver


Reply
Posts: 4092
(@skunberg)
Famed Member
Joined: 18 years ago

I have the smaller set and it's not there. I took a square bit and filed it down to size.


Reply
AuburnLights
Posts: 213
(@auburnlights)
Estimable Member
Joined: 12 years ago
jklingert wrote:Has anyone found the correct screwdriver to take out the triangle shaped screws?

One of the 4 (they aren't individually marked as far as I can tell) in this package works perfectly. I even used a 1/4 drive socket on the top of them to help break the epoxy seal on the screws. Worked great, not a single stripped screw.

Here's the Link (Edit also here)

ScrewDriver

Reply
Posts: 1076
 Zeph
(@zeph)
Noble Member
Joined: 15 years ago

I have GECE Icicles (20 per unit) older style (3 boxes). Would this controller work? And if it does, I suspect it would need a different case, right?

The box look likes this one: http://www.ebay.com/itm//141853427391 and the controller is white with a single button to change effects.


Reply
Posts: 691
(@stormyblade)
Honorable Member
Joined: 12 years ago
jklingert wrote:Any thoughts about waterproofing these? The original GECE controller had some sort of epoxy poured into the wire end in the trapezoid shaped cavity to stop water ingress along the wires. Has anyone found the correct screwdriver to take out the triangle shaped screws?

I bought a small precision screwdriver set off Amazon for $10 and it has a triangle tip that fits into these screws perfectly. Here's a link: http://www.amazon.com/Professional-Portable-Screwdriver-Extension-Maintenance/dp/B00FO18LZQ/ref=sr_1_2?s=hi&ie=UTF8&qid=1451878165&sr=1-2&keywords=jackly+precision+screwdriver If you mouse over the picture to enlarge it, the triangle tip is in the bottom row, left side of the tips.

As for waterproofing, I just used some outdoor-rated silicone I bought in a tube from Home Depot - I think it was less than $5.


Reply
Page 6 / 13
Share: