e68x and Wireless B...
 
Notifications
Clear all

e68x and Wireless Bridge using DD-WRT

11 Posts
7 Users
0 Reactions
5,931 Views
kychristmas
Posts: 3955
Topic starter
(@kychristmas)
Famed Member
Joined: 18 years ago
[#21086]

I am attempting to configure an old access point as a Wireless Bridge/Gaming Adapter. After a great deal of playing around, I ended up install DD-WRT firmware on the Access point. I have some success, but I don't believe it's working the best that it can. I have a Linksys Wireless router configured as a normal Wireless Router running WAP2 Encryption. I have a WAP54G with the DD-WRT Firmware on it configured as a Wireless Bridge - Client Mode.

I am unable to successfully use the Web Interface to manage the e680. When I open it up in the browser the page loads, but when I attempt to issue a command, I get a "connection reset" error. The good news is that I am able to send data to it from Vixen and it seem to work fine. My biggest concern is will there be any sort of delay issues when I add in another 1050 pixels.

btw... I tried an old gaming adaptor I had for a PS2/Xbox, but it did not support the Multicast mode that is required. I had the opposite. It didn't work in Vixen, but I was able to use the Web interface and to configure and run tests.

Is anyone using this type of setup. If so, any adivce?


10 Replies
Xenia
Posts: 1358
(@xenia)
Noble Member
Joined: 15 years ago

I have the exact same setup using two linksys wap54g's This setup video solved all of my issues.


Reply
Barnabybear
Posts: 1583
(@barnabybear)
Noble Member
Joined: 15 years ago

I just started working on the same thing last night. Thanks for the setup link.
Can anyone confirm that the switch part of the access point works as normal, and that mutipul E1.31 devices (dependant on the number of sockets) can be connected without an additional switch?


Reply
Materdaddy
Posts: 2368
(@materdaddy)
Famed Member
Joined: 16 years ago

I can confirm. I have that setup in my garage with a PC, an RPM E1.31->DMX bridge and an E681 connected.


Reply
Posts: 75
(@phillikl)
Trusted Member
Joined: 18 years ago

Was thinking on this very topic today.....

Now thinking outloud....
Switches/Bridges are by design to block broadcast and multicast traffic. E68X utilizes a network to broadcast its information or multicast to several networks and the controller ignores information that doesn't belong. The easiest way to think of a switch is the old telephone operators; you call te operator and they connect you to where you want to talk too. In therory a switch wouldn't work for this application, however there some software adjustments that could be made to bring this life.
Routers connect dissimilar networks, they do not block broadcast cast/multicast but limit it to a specific network. So setup should be easy, plug it up and join the wifi and go.

*Scratching head* looks like I might be digging through my box o old networking stuff to see what happens!!!

Side note: I would disable all the encryption stuff, all it does is create unnecessary tax on the wifi.


Reply
Barnabybear
Posts: 1583
(@barnabybear)
Noble Member
Joined: 15 years ago

I’m still waiting for my two D-link DIR-615s to arrive in the post – it occurred to me today that not only could a wireless bridge be used for providing data to the controllers – it could simplify the use of networked cameras. You could checkout the viewers of your show, keep an eye on your collection box, check all the elements of your show are working correctly without going outside and of cause keep an eye on your display elements over night.


Reply
Posts: 2171
(@mschell)
Noble Member
Joined: 18 years ago
phillikl wrote:Was thinking on this very topic today.....

Now thinking outloud....
Switches/Bridges are by design to block broadcast and multicast traffic. E68X utilizes a network to broadcast its information or multicast to several networks and the controller ignores information that doesn't belong. The easiest way to think of a switch is the old telephone operators; you call te operator and they connect you to where you want to talk too. In therory a switch wouldn't work for this application, however there some software adjustments that could be made to bring this life.
Routers connect dissimilar networks, they do not block broadcast cast/multicast but limit it to a specific network. So setup should be easy, plug it up and join the wifi and go.

*Scratching head* looks like I might be digging through my box o old networking stuff to see what happens!!!

Side note: I would disable all the encryption stuff, all it does is create unnecessary tax on the wifi.

I think you've got it twisted slightly.

Routers do not pass multicast or broadcast traffic. They do block multicast. That's why they "limit it to a specific network".

Switches and bridges typically do pass multicast and broadcast traffic to all their ports. That's why they are used within a location or building. Switches may not pass non-broadcast traffic to all ports if it knows that a packet is destined for a specific port, and that's why they are "better" than a hub, which sends everything to everyone.

A wireless "router" typically won't pass broadcast/multicast unless it's set in bridge mode, which makes it behave more like a switch than a router. But there are several options that can modify it's behavior to be somewhere in between.

And back to some of the original post. If you can't access the web page of the E681, when over wireless, you need to be sure the IP address of the E681 needs to be in the same subnet as your PC so that your PC can talk to the web server on the E681. For the lights to work, the PC sends that info via multicast, and the IP address doesn't matter.


Reply
jrock64
Posts: 1099
(@jrock64)
Noble Member
Joined: 19 years ago

If you just want a wireless connection to an E131 device, a simpler solution may be a few of these

http://www.bestbuy.com/site/Agptek+-...&skuId=5056127
or
http://www.amazon.com/Wireless-Dream.../dp/B005OIB6XI

I am using one here without problems.
http://doityourselfchristmas.com/forums/showthread.php?21984-Need-a-sanity-check-on-this-design-for-my-new-coat/page2

Joel


Reply
kychristmas
Posts: 3955
Topic starter
(@kychristmas)
Famed Member
Joined: 18 years ago
jrock64 wrote:If you just want a wireless connection to an E131 device, a simpler solution may be a few of these

http://www.bestbuy.com/site/Agptek+-...&skuId=5056127
or
http://www.amazon.com/Wireless-Dream.../dp/B005OIB6XI

I am using one here without problems.
http://doityourselfchristmas.com/forums/showthread.php?21984-Need-a-sanity-check-on-this-design-for-my-new-coat/page2

Joel

I saw your posts over the weekend. I appreciate your response here. Though the price-point is nice, I was trying to use what I already had on-hand. Wireless capability is not a requirement as my 680s will be less than 30 ft from a Network switch.

The pure gaming adaptors didn't seem to allow Multicast traffic to go through. I tried two differents ones. Glad to know that there's a tested, relatively inexpensive solution.

Did you leave your Wireless Network unsecured to make this work? Although, I would likely setup an independent wireless network for the display, it would be nice to keep everything secure.


Reply
jrock64
Posts: 1099
(@jrock64)
Noble Member
Joined: 19 years ago

Still testing on my home network.
Had to go unsecure to get it to work.
The E680 did not like me switching between the network cable, and the wireless access for some reason.
Normally I go with an access list, so if your MacID is not on the list, you do not get in.

My show will be running on a different network, with just the show computer, and no network, or internet access.
I guess that is one more reason to turn the webserver off on the E680s

Joel


Reply
Page 1 / 2
Share: