Notifications
Clear all

E682 and lor s3

16 Posts
8 Users
0 Reactions
7,851 Views
Posts: 73
Topic starter
(@ratroder)
Trusted Member
Joined: 17 years ago
[#21256]

Don't know if this should be in the lor lagoon or no. Please move if necessary.

I am looking to set up my e682 to lor s3. The e682 is connected to a switch and the computer is on the same. The e682 web server is accessible and I can run all the tests just fine. But lor won't send sequence commands to the controller or well the pixel strips won't light. The green light on the mag jack blinks but the green status light on the board is off or comes on dim sometimes.

I am using 1804 pixels by the way.


15 Replies
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago

You will need to share a lot more info .

how are you connecting to the 682 through a router or directly from nic to switch ?

is lor setup and configured for e1.31 and correct universe etc?

could you post a pic of the 682 config ?


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

For LOR E1.31 don't you have to keep a utility open at all times - I don't recall the name of it but I seem to recall reading a post about it...


Reply
Donny M. Carter
Posts: 1008
(@donny-m-carter)
Noble Member
Joined: 16 years ago
budude wrote:For LOR E1.31 don't you have to keep a utility open at all times - I don't recall the name of it but I seem to recall reading a post about it...

Yes, LORCommListener!


Reply
Posts: 73
Topic starter
(@ratroder)
Trusted Member
Joined: 17 years ago

The e682 is connected to a switch and the computer is on the same switch. Then the switch runs to my router then to my modem.

The commonlistner is working too. All the universes come up and are recognized. I have 4 universes going to my lynx etherdogle. Then 5-10 are going to the e682.


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

Please post a screen capture of your E682 configuration screen. Make sure the tester is shut off - 'TE 0' then 'SA 0'.


Reply
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago

as brian said ,

in 682 command line

Test 0

save 0

quit 10 to free web config


Reply
Posts: 2171
(@mschell)
Noble Member
Joined: 18 years ago
angus40 wrote:as brian said ,

in 682 command line

Test 0

save 0

quit 10 to free web config

On the E682, you don't need to kill the web config, since there's a dedicated processor handling that now. So the last line 'quit 10' isn't needed.

Can you send any data to the E682 with something besides LOR S3? SACNview is a good tool to send data via E1.31 to check configuration of E682. But posting a screen shot of your config will help us help you.


Reply
Jeff Millard
Posts: 1450
(@jeff-millard)
Noble Member
Joined: 19 years ago

I made a simple checklist that might cover something you may have missed. It doesn't cover any settings for the E682 since it's on the LOR help Forum. But there are a couple things in there that might be roadblocks to getting the lights to blinky/flashy.

Jeff


Reply
Posts: 73
Topic starter
(@ratroder)
Trusted Member
Joined: 17 years ago

Interesting. The help page worked. Didn't know that the e682 ran on multicast. I specified the ip from the beginning. but got it to work now. Thanks for the help.


Reply
Page 1 / 2
Share: