I talked to Ray about these two strips, WS2811 non-waterproof and WS2811 Waterproof, and ask if a 30 led/ws2811 version would be coming. He talked to the factory and they will be doing one.
In case you didn't notice this is the one with the WS2811 inside the 5050 RGB LED.
I missed the waterproof version so I edited the first post and added it Even at $14 per meter not bad for 60 LED/Pixels per meter. Based on that I would expect to see the 30 per meter right at $6.50 to $7.50 per meter. At that price and assuming no reliability issues I'm not sure I'd even bother to use the 12V 30 LED 10 pixel product and just stay with the 5V 30 pixel one.
Just got an email from Ray. The factory is getting ready to make the new WS2811 30 Pixel per meter 5 meter strip. Here is the link to the pixel strip. The price, $38 for 5 meters, that's $7.60 per meter. That's a darn good price so I won't be getting the 30 LED 10 IC version.
Note the picture is the 60 Pixel per meter until Ray can get a picture of the new one and some of the technical data needs editing. I figure the strip will draw about 8A or may a tad more.
timon wrote:I talked to Ray about these two strips, WS2811 non-waterproof and WS2811 Waterproof, and ask if a 30 led/ws2811 version would be coming. He talked to the factory and they will be doing one.In case you didn't notice this is the one with the WS2801 inside the 5050 RGB LED.
why would it have the 2801 inside the 2811 ?
Sorry, typo.
i thought you may have inside scoop on ws2801 with ic in the led .
Just to make sure I understand this correctly.....
Each LED will be individually addressable instead groups of 3, meaning one 5m strip will eat up 450 channels instead of 150 ?
see these threads
http://doityourselfchristmas.com/forums/showthread.php?22196-Looked-inside-a-5050-LED-lately
http://doityourselfchristmas.com/forums/showthread.php?21984-Need-a-sanity-check-on-this-design-for-my-new-coat
I have 3 rolls, 12meters of these.
Yes every LED is individually controllable and the spacing is less than 3/4 inch.
At 60/m, every 2.5m is one universe.
These things will eat an E680 for lunch and ask for seconds.
Joel
jrock64 wrote:see these threads
http://doityourselfchristmas.com/forums/showthread.php?22196-Looked-inside-a-5050-LED-lately
http://doityourselfchristmas.com/forums/showthread.php?21984-Need-a-sanity-check-on-this-design-for-my-new-coatI have 3 rolls, 12meters of these.
Yes every LED is individually controllable and the spacing is less than 3/4 inch.
At 60/m, every 2.5m is one universe.
These things will eat an E680 for lunch and ask for seconds.Joel
with this type of strip you may need to look at Dvi controller/slave setup.
I mentioned this a few months back about led strip with the ic inside the led.
One master controller can run 2 x 255 slave controllers with up to 16 universe control for each slave device .
Yes, that correct.
If you want it to look like the 10 pixel strip then you can set the controller to combine pixels. Why would you want to combine pixels instead of getting the 50 pixel strip that already combines LEDs? Flexibility, you can set the to triples now and later go to doubles or all the way to singles later.
These also gives you a closer cutting distance. Instead of 4" cuts you can cut them every 1.3". This can make it easier to do windows or any other prop.
For the price I don't think you can beat this new strip. It a very good price for a very flexible strip.
Lionking_Tx wrote:Just to make sure I understand this correctly.....Each LED will be individually addressable instead groups of 3, meaning one 5m strip will eat up 450 channels instead of 150 ?
