If using multicast the only settings are universe number and number of channels? Correct?
Skunberg wrote:If using multicast the only settings are universe number and number of channels? Correct?
You also have to make sure the box is checked for "active" and choose what network adapter to use from the drop down list. If you only have one on your show pc, then select the option that doesn't contain the word "loopback" (may not have that depending on the OS).
On a similar note, in terms of vixen 'channels'. I want the the following hardware setup:
U1: DMX output using RPM Dongle (Channels) 1 - 249
U10: E1.31 controlling E681(1) group 1, 450 channels (150 pixels)
U11: E1.31 controlling E681(1) group 2, 450 channels (150 pixels)
U12: E1.31 controlling E161(1) Group 3, 300 Channels (100 pixels)
U13: E1.31 controlling E161(1) Group 4, 432 channels (144 pixels)
U14: E1.31 controlling E161(2) Group 1, 450 channels (150 pixels)
U15: E1.31 controlling E161(2) Group 2, 450 channels (150 pixels)
U16: E1.31 controlling E161(2) Group 3, 450 channels (150 pixels)
U17: E1.31 controlling E161(2) Group 4, 450 channels (150 pixels)
Since I am not using full universes (512), when creating channels in vixen, do I leave empty channels in between universes or number my outputs consecutively based on what I am using? Basically, Do I create 512 channels in Vixen for each universe or just the number I intend to use?
michaelc wrote:On a similar note, in terms of vixen 'channels'. I want the the following hardware setup:
U1: DMX output using RPM Dongle (Channels) 1 - 249
U10: E1.31 controlling E681(1) group 1, 450 channels (150 pixels)
U11: E1.31 controlling E681(1) group 2, 450 channels (150 pixels)
U12: E1.31 controlling E161(1) Group 3, 300 Channels (100 pixels)
U13: E1.31 controlling E161(1) Group 4, 432 channels (144 pixels)
U14: E1.31 controlling E161(2) Group 1, 450 channels (150 pixels)
U15: E1.31 controlling E161(2) Group 2, 450 channels (150 pixels)
U16: E1.31 controlling E161(2) Group 3, 450 channels (150 pixels)
U17: E1.31 controlling E161(2) Group 4, 450 channels (150 pixels)Since I am not using full universes (512), when creating channels in vixen, do I leave empty channels in between universes or number my outputs consecutively based on what I am using? Basically, Do I create 512 channels in Vixen for each universe or just the number I intend to use?
There is no need to leave blank channels - just make sure you get the right start addresses configured in the plug-in.
You have to have the same amount of channels in V3 as you have configured in your controllers. If you have a controller cluster configured for 150 channels but you are only using 147 because you have 49 pixels you need to configure 150 channels in V3 and leave the last 3 un-patched. That is the only time you should have blank channels.
ok, so in my first universe where I'm using DMX. I'm currently only using 249 channels but I may be adding to that universe down the road. For that one, I'd like to leave the blank channels as placeholder, so my plan is to start my E681 on U10 and channel 513.
In V2, I would have to create the add'l 263 channels in vixen (to get to 512), Then I can add all my pixel channels that I'm using starting with channel 513. Does this sound like it would work.
And in Vixen Setup, would it look like this
Thank you! Turned out I had the wrong universe number.


